Abstract:Based on a critical analysis of the current state and prospects of development of the problem of pyrometallurgical recovery/extraction of aluminum from aluminum-bearing industrial waste, the need to replace traditional, electrocarbonothermic processes and melting process units with innovative, plasma carbothermal processes and furnace-reactors, with the possibility of reverse feeding and recovery of gasified during melting metal and metal oxide components is substantiated. On the basis of this analysis a new technological scheme of smelting with a new design of plasma-arc furnace-reactor, which provides a solution to the problem using a special hollow double-shell graphite cathode connected to the system of circulating supply of gases separated from the reaction zone, was developed and presented. The proposed technological scheme also differs in the use of such highly active liquid and gaseous reagents as carbon-containing reducing agents as calcium carbide (CaC2) and methane (CH4). The main features of chemism of reducing processes are described. It is shown that by replacing traditional coke with anodized calcium carbide and natural gas (methane) the recovery rate of aluminum oxide (Al 29-34%) and silica (SiO2) and hematite (Fe2O3) present with it increases to 80-99%. Specific power consumption is reduced by 35-40%, the 90-95% reduction in the loss of target elements, the 80% reduction in the emission of greenhouse carbon dioxide, which is replaced by a very valuable recyclable synthesis gas - CO-H2. By additionally feeding separate portions of quartzite and steel-rolling scale in the furnace-reactor, a complex alloy-ligature of Fe-Si-Al-Ca system is melted, with the ratio of components: 1:[1.3-2]:[1.3-1.2]:[0.9-1.25]. With the introduction into industrial practice of the plasma carbothermal process of aluminum reduction from secondary aluminum dumping slags accumulated in the world (4 million tons/year), it will be possible to return up to 1-1.5 million tons/year of aluminum to the production processing cycle.

Study of the process of cerium restoration by aluminum and calcium carbide from cerium-containing slag

Thermodynamic Analysis of the Oxidation Behavior of Cerium in High‐Speed Steel during Electroslag Remelting

Structure and viscosity of slags containing cerium oxide

Aluminothermic Reduction of CeO2: Mechanism of an Economical Route to Aluminum-Cerium Alloys

Effect of cerium on the primary carbides and inclusions in electroslag remelted M35 high speed steel

Effect of CeO2 Content on Melting Performance and Microstructure of CaO-Al2O3-SiO2-MgO Refining Slag

Processing of Rare Earth Metal Oxide for Use as a Master Alloy in the Metallurgical Industry

Cerium extraction by metallothermic reduction using cerium oxide powder injection

Cerium in aluminum alloys

Development and investigation of the technological process of plasma carbothermal reduction of slag from secondary metallurgy of aluminum

Carbothermic Smelting Reduction of Copper Slag for Fe and Cu Recovery Using Calcium Aluminate Refining Slag as the Modifier

Assessment of Inclusion Removal Ability in Refining Slags Containing Ce2O3

Study on mechanism of refining and modifying in Al-Si-Mg casting alloys with adding rare earth cerium

Experimental Study on Thermodynamics of CaO–SiO2–Ce2O3–5wt.% Al2O3 System at 1773 K

Effect of Ce 2 O 3 on Structure, Viscosity, and Crystalline Phase of CaO-Al 2 O 3 -Li 2 O-Ce 2 O 3 Slags

Improved High-Temperature Aluminum Alloys Containing Cerium

Influence of cerium treatment on inclusion modification and as-cast microstructure of high-strength low-alloy steel

Equilibrium content of lanthanum in metal under the slag of СаО – SiO2 – La2O3 – 15 % Al2O3 – 8 % MgO system

Investigation of the Effect of Cerium on the Structure and Properties of Calcium-Containing Aluminum Alloys

Aluminothermic Reduction Kinetics of Calcium Silicate Slag for Silicon Alloy Production