Abstract:The acid–base chemistry at the interface of zinc oxide (ZnO) and methylammonium lead tri-iodide (perovskite) leads to a proton transfer reaction that results in perovskite degradation. In perovskite solar cells (PSCs), this reaction produces low efficiency and reduces the long-term stability. In this work, an aluminum (Al) layer of 1–2 nm thickness is thermally evaporated on top of ZnO or Al3+-doped ZnO (ZnO:Al) thin films and then annealed at 450 °C for 30 min. Thermal annealing converts the surface aluminum film into a transparent and approximately 2 nm thick aluminum oxide (AlOx) layer. Also, a larger concentration of oxygen vacancies is obtained by the annealing of Al and attributed to the diffusion of Al into the ZnO surface, and the ZnO underlayer results in a more conductive material. As a result, the chemical stability of perovskite coatings on top of AlOx-coated ZnO films is significantly enhanced, and the flat-band level of ZnO shifts 0.09 eV upwards, which improves the energetic level alignment in PSCs. This allows us to obtain ZnO:Al/AlOx-based planar PSCs that show a maximum efficiency of 16.56% with the perovskite layer prepared in ambient conditions under a relative humidity of 40–50%. After continuous illumination of about 30 min in air, ZnO-based PSCs without AlOx layer retain only 34.5% of their original efficiency, whereas those with AlOx retain about 92.5%. It is demonstrated that thermal evaporation–oxidation is an efficient method to modify the surface properties of inorganic semiconductor thin films and improves both the performance and stability of PSCs.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.0c01106?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.0c01106</a>.XPS spectra of Zn and Al; XRD patterns, optical transmittance spectra and deconvolution of PL spectra of ZnO thin films; Bode diagrams at 0 V in dark and under illumination, at 900 mV in dark and under illumination of ZnO/AlOx and ZnO:Al/AlOx samples; CV curves of the four ZnO samples in an electrolyte of 0.1 M (CH3CH2CH2CH2)4N(PF6) in acetonitrile; EIS measurements of the four ZnO samples; flat-band, charge carrier concentration, and electronic levels of the four ZnO films; forward and reverse J–V curves and HI of freshly prepared PSCs with four different ZnO films; J–V curves of five freshly prepared PSC samples for each type of ZnO; and photovoltaic parameters of PSCs based on four different ZnO films as a function of shelf life time (storage time) in ambient conditions (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.0c01106/suppl_file/ae0c01106_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Effects of Al2O3 Rear Interface Passivation on the Performance of Bifacial Kesterite‐Based Solar Cells with Fluorine‐Doped Tin Dioxide Back Contact

The effect of Al2O3 on the performance of perovskite solar cells

Efficiency improvement of PERC solar cell using an aluminum oxide passivation layer prepared via spatial atomic layer deposition and post-annealing

Influence of Al2O3/SiNx Rear-Side Stacked Passivation on the Performance of Polycrystalline PERC Solar Cells

Efficiency enhancement of perovskite solar cells based on Al2O3-passivated nano-nickel oxide film

The Role of Hydrogen from ALD‐Al2O3 in Kesterite Cu2ZnSnS4 Solar Cells: Grain Surface Passivation

Enhanced Si Passivation and PERC Solar Cell Efficiency by Atomic Layer Deposited Aluminum Oxide with Two-step Post Annealing

Effects of CuAlO2 on the heterojunction interface and performance of Cu2ZnSn(S,Se)4 thin-film solar cells

Boosting Kesterite Solar Cell Performance with Tantalum Oxide Passivation Layer and In Situ Formed Point Contacts

Interfacial engineering of mp-TiO2/CH3NH3PbI3 with Al2O3: Effect of different phases of alumina on performance and stability of perovskite solar cells

Modulation of Field-Effect Passivation at the Back Electrode Interface Enabling Efficient Kesterite-Type Cu 2 ZnSn(S,Se) 4 Thin-Film Solar Cells

Tuning Back Side Passivation for Enhancing the Performance of PERC Solar Cells

Enhancing kesterite-based thin-film solar cells: A dual-strategy approach utilizing SnS back surface field and eco-friendly ZnSe electron transport layer

Thermal Evaporation–Oxidation Deposited Aluminum Oxide as an Interfacial Modifier to Improve the Performance and Stability of Zinc Oxide-Based Planar Perovskite Solar Cells

Microstructural Passivation of Patterned Al2O3 Back Contacts on CdS/CdTe Solar Cells

Modification of Back Contact in Cu 2 ZnSnS 4 Solar Cell by Inserting Al-Doped ZnO Intermediate Layer

Passivation of Interfaces in Thin Film Solar Cells: Understanding the Effects of a Nanostructured Rear Point Contact Layer

Mitigated Front Contact Energy Barrier for Efficient and Stable Perovskite Solar Cells

Simultaneous Passivation of the SnO 2 /Perovskite Interface and Perovskite Absorber Layer in Perovskite Solar Cells Using KF Surface Treatment

The Application of Al2tio5 at the Tio2/Perovskite Interface to Decrease Carrier Losses in Solar Cells

Simultaneous Surface Modification and Defect Passivation on Tin Oxide–Perovskite Interfaces using Pseudohalide Salt of Sodium Tetrafluoroborate