Abstract:This study focuses on the microstructure evolution of non-oriented silicon steel for the drive motor iron core of new energy vehicles. The Fe-3.0% Si non-oriented silicon steel hot-rolled bands were taken as the research objects and were normalized at 700, 800 and 900 °C for 3 and 10 min. The influence of low-temperature normalization process on the microstructure, texture and mechanical properties was studied. The results show that the bands normalized at 700 and 800 °C inherit the gradient microstructure and texture characteristics of the initial hot-rolled band. The surface layer consists of homogeneous and fine recrystallized grains, the central layer consists of elongated deformed grains with γ-fiber and α-fiber textures and the subsurface layer has mixed grain structure with strong Goss texture. When the normalizing temperature is increased to 900 °C, the normalized band is completely recrystallized, and the gradient structure and texture are significantly weakened. During the normalizing process, the θ-fiber oriented grains in the subsurface mainly nucleate at the grain boundaries of the α*-fiber and //ND matrix grains, and the //ND oriented grains mainly nucleate at the grain boundaries of Goss and {110} deformed matrix grains. The θ-fiber oriented grains in the central layer mainly nucleate at the grain boundaries of {001} , γ-fiber and {114} matrix grains, the α-fiber oriented grains nucleate in the {111} and α-fiber deformed matrix grains, the nucleation of α*-fiber grains is related to the α-fiber deformed matrix grains. After normalizing at 900 °C, θ-fiber and α*-fiber grains have growth advantages, resulting in strong θ-fiber and α*-fiber textures. As the normalizing temperature increases, the gradient structure of the normalized microstructure is gradually weakened, thus leading to the decrease in plastic deformation ability.

Effect of Normalizing Treatment on Microstructure and Mechanical Properties of Non-oriented Fe-3.0% Si Steel

Effect of normalizing cooling process on microstructure and precipitates in low-temperature silicon steel

EFFECT OF COLD ROLLING PROCESS ON TEXTURE EVOLUTION OF GRADIENT MICROSTRUCTURE IN Fe-3,0 % Si NON-ORIENTED SILICON STEEL

Effect of Normalization Process on the Microstructure and Properties of Annealed Cold-Rolled Sheet of Oriented Silicon Steel

Roles of Silicon Content and Normalization Temperature on Cold Workability and Recrystallization of High-Grade Non-Oriented Silicon Steel

Effect of Normalizing Temperature on Microstructure and Properties of Low-Carbon and Low-Silicon Non-oriented Silicon Steel Prepared by TSCR Process

Comprehensive Influence of the Normalized and Final Annealing Process on High‐Strength Nonoriented Silicon Steel

Effect of recrystallization annealing temperature on microstructure, texture and magnetic properties of non-oriented silicon steel produced by strip casting

Effect of Grain Size Before Cold Rolling on Microstructure, Texture and Magnetic Properties of Ultra-Thin Low-Si Non-oriented Silicon Steel

Effect of microstructure modification on magnetic and mechanical properties of high-grade non-oriented silicon steel during annealing treatment

Development of thin-gauge low iron loss non-oriented silicon steel

Thick-Gauge Ultra-High-Strength High-Silicon Non-Oriented Silicon Steel with Balanced Mechanical and Magnetic Properties Controlled by Partial Recrystallization Annealing

Influence Mechanisms of Cold Rolling Reduction Rate on Microstructure, Texture and Magnetic Properties of Non-Oriented Silicon Steel

Effect of Holding Time of Decarbonization Annealing on Recrystallization in Fe-3.2%Si-0.047Nb% Low-Temperature Oriented Silicon Steel

Microstructure and texture evolution of ultra-thin high grade non-oriented silicon steel used in new energy vehicle

Improvement of magnetic properties via normalizing annealing for high-strength Fe-4.5wt.%Si electrical steel

Dependence of recrystallization behavior and magnetic properties on grain size prior to cold rolling in high silicon non-oriented electrical steel

Effect of Cold Rolling Process on Microstructure, Texture and Properties of Strip Cast Fe-2.6%Si Steel

Fabrication of high-performance low silicon non-oriented electrical steels by a new method: Low-finishing-temperature hot rolling combined with batch annealing

Influence of Annealing Process on Microstructures,Mechanical and Magnetic Properties of Nb-Containing High-Strength Non-Oriented Silicon Steel

Effects of Continuous Rolling and Reversible Rolling on 2.4% Si Non-Oriented Silicon Steel