Abstract:This paper reviews the history, the present status and possible future developments of photovoltaic (PV) materials for terrestrial applications. After a brief history and introduction of the photovoltaic effect theoretical requirements for the optimal performance of materials for pn-junction solar cells are discussed. Most important are efficiency, long-term stability and, not to be neglected, lowest possible cost. Today the market is dominated by crystalline silicon in its multicrystalline and monocrystalline form. The physical and technical limitations of this material are discussed. Although crystalline silicon is not the optimal material from a solid state physics point of view it dominates the market and will continue to do this for the next 5–10 years. Because of its importance a considerable part of this review deals with materials aspects of crystalline silicon. For reasons of cost only multicrystalline silicon and monocrystalline Czochralski (Cz) crystals are used in practical cells. Light induced instability in this Cz-material has recently been investigated and ways to eliminate this effect have been devised. For future large scale production of crystalline silicon solar cells development of a special solar grade silicon appears necessary. Ribbon growth is a possibility to avoid the costly sawing process. A very vivid R&D area is thin-film crystalline silicon (about 5–30μm active layer thickness) which would avoid the crystal growing and sawing processes. The problems arising for this material are: assuring adequate light absorption, assuring good crystal quality and purity of the films, and finding a substrate that fulfills all requirements. Three approaches have emerged: high-temperature, low-temperature and transfer technique. Genuine thin-film materials are characterized by a direct band structure which gives them very high light absorption. Therefore, these materials have a thickness of only one micron or less. The oldest such material is amorphous silicon which is the second most important material today. It is mainly used in consumer products but is on the verge to also penetrate the power market. Other strong contenders are chalcogenides like copper indium diselenide (CIS) and cadmium telluride. The interest has expanded from CuInSe2, to CuGaSe2, CuInS2 and their multinary alloys Cu(In,Ga)(S,Se)2. The two deposition techniques are either separate deposition of the components followed by annealing on one hand or coevaporation. Laboratory efficiencies for small area devices are approaching 19% and large area modules have reached 12%. Pilot production of CIS-modules has started in the US and Germany. Cadmium telluride solar cells also offer great promise. They have only slightly lower efficiency and are also at the start of production. In the future other materials and concepts can be expected to come into play. Some of these are: dye sensitized cells, organic solar cells and various concentrating systems including III/V-tandem cells. Theoretical materials that have not yet been realized are Auger generation material and intermediate metallic band material.

On the feasibility of multi-polymer, liquid-crystal silica photovoltaics: simulating diodic p-n junctions with ionic gradients

Mechanically Robust and Self-Cleaning Antireflective Coatings for Photovoltaic Modules

Photovoltaic materials, history, status and outlook

Colorful conducting polymers for vivid solar panels

Evolution of Polymer Photovoltaic Performances from Subtle Chemical Structure Variations.

Polysilicon passivated junctions: The next technology for silicon solar cells?

Amorphous Silicon Particles/Polyaniline Composites for Hybrid Photovoltaic Solar Cell: an Experimental Feasibility Study

Delayed Crystallization Kinetics Allowing High-Efficiency All-Polymer Photovoltaics with Superior Upscaled Manufacturing

A Cdse Nanocrystal Meh-Ppv Polymer Composite Photovoltaic

All Polymer Photovoltaics: from Small Inverted Devices to Large Roll-to-roll Coated and Printed Solar Cells

Efficient Polymer Photovoltaic Devices Based on Polymer D-A Blends

Rational Design and Elucidation of Interfacial Dynamics in PMMA/PVDF Compatibilized Blends Through Solution Blending for Stable Quasi-Solid-State Dye-Sensitized Solar Cells

Simulation-based roadmap for the integration of poly-silicon on oxide contacts into screen-printed crystalline silicon solar cells

Highly Efficient Hybrid Polymer and Amorphous Silicon Multijunction Solar Cells with Effective Optical Management

Aggregation‐Induced Multilength Scaled Morphology Enabling 11.76% Efficiency in All‐Polymer Solar Cells Using Printing Fabrication

Polymer Photoelectrodes for Solar Fuel Production: Progress and Challenges

Interfacial Ion Transport in Porous Polydimethylsiloxane–Polydopamine Composites for Solar Thermoelectric Conversion

Delayed Crystallization Kinetics Allowing High‐Efficiency All‐Polymer Photovoltaics with Superior Up‐Scaled Manufacturing

High-Efficiency Triple-Junction Polymer Solar Cell: A Theoretical Approach

Solution-Processible Conductive Organics For Efficient Polymer And Perovskite Solar Cells

High-performance semitransparent polymer solar cells floating on water: Rational analysis of power generation, water evaporation and algal growth