Abstract:Journal of Composite Materials, Ahead of Print. Carbon fiber-reinforced composites have become increasingly favored in the aerospace and automotive sectors for their remarkable performance attributes. Nonetheless, their broader adoption is hindered by the concern of delamination. To address this limitation, our study delved into the influence of incorporating a thermoplastic toughening agent on the interlaminar fracture toughness (ILFT) of woven carbon fiber composites. Our investigation focused on the impact of diverse curing pressures on these composites, analyzing configurations both with and without an integrated non-woven polyamide (PA) veil. The PA veil was meticulously positioned within the central layer of a composite, combining benzoxazine and carbon fiber constituents. Our primary objective entailed optimizing curing conditions to enhance ILFT across both Mode-I and Mode-II fracture modes. Our findings unveiled that elevating curing pressure had a limited effect on ILFT in non-interleaved composites while interleaved samples exhibited substantial ILFT reductions under heightened curing pressure. Raising pressure from 1 atm to 3.5 atm caused approximately a 27% drop in the Mode-I strain energy release rate (GIC) value, and this reduction deepened to 42% at 7 atm. This highlighted the inverse relationship between increased curing pressure and GIC values in interleaved specimens, while non-interleaved counterparts experienced less pronounced changes. A parallel trend manifested in Mode-II ILFT, where escalated curing pressure correlated with diminished Mode-II strain energy release rate (GIIC) values. Interleaved samples suffered a notably more significant decline, attributed to resin content reduction caused by heightened pressure. This, in turn, compromised the bond between the PA veil and the matrix, facilitating the propagation of cracks within the composite. This ultimately culminated in significantly reduced GIC and GIIC values. Our study contributes valuable insights into optimizing the interlaminar fracture toughness of carbon fiber composites, shedding light on the complex interplay of curing conditions and material configurations.

Experimental investigation of warpage in thin CF/PEKK composite laminates consolidated under non-isothermal conditions

Comparison of the in situ compressive behavior of carbon fibers woven ply laminates exposed to one‐sided heat flux: Thermoplastic versus thermosetting composites

Warpage investigation of carbon/PEEK discontinuous long fibre thin panels

Effect of processing parameters on degree of crystallinity and mechanical performance of CF/PEKK aerospace composites

Understanding the Impact of Fibre Wrinkle Architectures on Composite Laminates Through Tailored Gaps and Overlaps

Investigation on the Compressive Mechanical Properties of Ultra-Thick CFRP Laminates

Influence of Process Parameters on the Interlaminar Shear Strength of CF/PEEK Composites In-Situ Consolidated by Laser-Assisted Automated Fiber Placement

An experimental validation study of a numerical modeling approach to predicting post-consolidation dimensions of thermoplastic composites

Experimental Study on Warpage Phenomenon of Wax Parts Manufactured by Fused Filament Fabrication

Influence of thermal history and consolidation force on wedge peel strength of CF/PEEK laminates manufactured by laser‐radiated in‐situ consolidation

Investigation of interlayer toughening of carbon fiber composites using non-woven polyamide veils under different curing pressures

Experimental study of warpage and shrinkage in injection molding of HDPE/rPET/wood composites with multiobjective optimization

Relaxation behavior of thin-ply high strain composites using a dynamic mechanical analyzer based column bending test

The effects of processing parameters on the wedge peel strength of CF/PEEK laminates manufactured using a laser tape placement process

Experimental Study on the Influence of Optimised Automated Fibre Placement Processing Parameters on the Impact Response and Residual Flexural Strength of AS4/APC-2 Laminates

Experimental Investigation of Processing Welding Parameters for PPS/Carbon Fiber Laminates for Aeronautical Applications

Discussion on Manufacturing Process of Unsymmetric Composite Laminates

A Study on Process-Induced Warpage of Curing Mold of Composite Structures

Short fibre/unidirectional hybrid thermoplastic composites: Experimental characterisation and digital analysis

Effects of Process Parameters in Thermoforming of Unidirectional Fibre-Reinforced Thermoplastics

The effect of laser assisted tape placement processing conditions on microstructural evolution, residual stress and interlaminar shear strength of carbon fibre/PEEK laminates