Abstract:Mechanism analysis, process optimisation and validation of laser surface treatment. Adhesive bonding has gradually replaced mechanical connections as the primary method for composite material bonding, with surface quality being the key factor determining the effectiveness of composite material adhesion. Laser surface treatment, known for its green and precise characteristics, has garnered widespread attention from both academia and industry. However, the process parameters of laser surface treatment are complex, efficiency is low, and the mechanism remains unclear. This paper, based on the response surface methodology (RSM), investigates the influence of laser secondary parameters on the resin removal rate of carbon fiber reinforced polymer/plastic (CFRP) surfaces and the impact of defocusing on surface treatment efficiency. The results indicate that when the total laser energy density (Et) is 69 J/cm2, the overlap ratio in the warp direction (OLs) is 76%, and the overlap ratio in the weft direction (OLh) is 85%, the surface tensile shear strength increases by 90.59% and 27.77% compared to the original surface and polished surface, respectively. When the defocus distance is +8 mm, the efficiency of laser surface treatment is 2.25 times that of non‐defocus, with minimal impact on mechanical performance. The surface treatment mechanism, with changes in Et, primarily involves the pure thermal decomposition of the resin matrix in an oxygen‐free environment, oxidative decomposition, and the synergistic action of the decomposition products' oxidation. Through the coupled optimization of laser process parameters, this work enhances the efficiency and effectiveness of composite material adhesive surface treatment, promoting the engineering application of laser technology. Highlights By establishing a response surface model, the study elucidated the impact patterns of laser secondary parameters (overlap rates in the warp and weft directions, total energy density) on the resin removal rate of CFRP surfaces. Based on the laser surface treatment phenomena at different total energy densities, the study analyzed and revealed the mechanism of near‐infrared (1064 nm) laser resin removal from CFRP surfaces. By increasing the spot size through defocusing, the efficiency of laser surface treatment was enhanced, and the impact on the interfacial properties of CFRP after defocused treatment was validated.

A portable fiber laser thermography system with beam homogenizing for CFRP inspection

Ultrasonic Inspection Of Localized Defects In Low-Porosity Cfrp

Defect Detection Method for CFRP Based on Line Laser Thermography

INTEGRATED TECHNOLOGY FOR DETECTION AND REPAIR OF MECHANICAL COMPONENT SURFACE FATIGUE MICROCRACKS USING PULSED LASER

Identifying Delamination in Carbon Fiber Composites Based on Defect Modes in Imperfect Phononic Crystals

Characterization and depth detection of internal delamination defects in CFRP based on line laser scanning infrared thermography

Quantitative non-destructive evaluation of CFRP delamination defect using laser induced chirp-pulsed radar photothermal tomography

Automatic Detection of CFRP Subsurface Defects via Thermal Signals in Long Pulse and Lock-In Thermography

The Feature Recognition of CFRP Subsurface Defects Using Low-Energy Chirp-Pulsed Radar Thermography

Detection and identification of delamination defects in CFRP laminates using nonlinear frequency-modulated infrared thermal wave testing technology

Investigation on ablative process of CFRP laminates under laser irradiations

3D photothermal reconstruction of subsurface defects in notched multidirectional CFRP laminates due to tensile fatigue loading

Optimization of Thermal-Wave Radar Thermography by Transverse Heat Flow Suppression Technique for Accurate Defect Detection of CFRP Laminates

Experimental Investigation on Ablation Behaviors of CFRP Laminates in an Atmospheric Environment Irradiated by Continuous Wave Laser

Joint Scanning Laser Thermography Defect Detection Method for Carbon Fiber Reinforced Polymer

Process optimization and performance verification of CFRP laser surface modification

Experimental study on infrared phase-locked thermal imaging inspection of carbon fiber reinforced polymer laminates

Non-contact detection of the interfacial microdefects in metal/CFRP hybrid composites using air-coupled laser ultrasound

Optimized ultrasonic total focusing imaging of diverse and multiple defects in crossply CFRP: Floquet wave theory, numerical simulation, and experimental validation

Ultrasonic Phased Array Imaging Approach Using Omni-Directional Velocity Correction for Quantitative Evaluation of Delamination in Composite Structure

Study on anisotropic heat transfer and thermal damage in nanosecond pulsed laser processing of CFRP