Abstract:Superconducting spherical shells may not only provide an appealing platform for exploring superconductivity in three-dimensional (3D) geometries with curved surfaces, but also be practically applied in important fields, such as in gyroscopes and gravimeters. In inertial confinement fusion (ICF), the perturbation on the target capsule caused by traditional contact support methods is recognized as one of the major contributors to performance degradation in ICF implosions. It was proposed recently that coating the capsule with a thin superconducting MgB2 spherical shell to realize non-contact support by means of magnetic levitation at the required temperatures similar to 20 K might offer a promising solution to this longstanding problem. To simulate the coating of ICF capsules, we deposited MgB2 spherical shells onto polycrystalline Si3N4 spheres (diameter d= 2 mm and 1 mm) via a hybrid physical-chemical vapour deposition technique. For both diameters, the spherical shells, of about 1 mu m in thickness and covering the whole spheres completely, were polycrystalline with thin plate-shaped MgB2 crystallites oriented randomly and closely connected. The spherical shells exhibited superconducting transition at a zero resistance temperature T-c(zero) c of 38.5-39.4 K in four-probe resistance measurements and ideal diamagnetism at low temperatures in magnetization measurements, suggesting the good crystallinity and homogeneity of the shells. The upper critical field H-c2, the irreversibility field H-irr and the lower critical field H-c1 were characterized and showed similar magnitudes and temperature dependencies for the d= 2 mm and 1 mm shells, yielding H-irr of 7-8 T and H-c1 of 7-12 mT at 20 K. The superconducting critical current density J(c) values, evaluated from the magnetization hysteresis loops, were 1.8x10(6) A cm(-2) and 8.5x10(4) A cm(-2) at 20 K under zero and 2 T applied field, respectively, for the d= 1 mm shell. The occurrence of small flux jumps was observed at low temperatures up to 12 K and in low fields below 0.3 T. The results demonstrate the feasibility of fabricating MgB2 spherical shells with properties applicable to potential areas employing magnetic levitation such as in ICF and that MgB2 spherical shells may be exploited as an experimental system to study superconductivity in 3D curvilinear geometry.

Very strong levitation force and stability achieved with a large MgB 2 superconductor disc

Investigations of the behaviour of superconducting magnetic levitating set-ups including a large MgB2 disc and a smaller NdFeB magnet.

The levitation force and stiffness enhancement of single domain GdBCO bulk superconductor by an axial background magnetic field

Lateral Displacement Influence on the Levitation Force of YBCO Coated Conductor Linear Bearings

Bulk superconducting materials as a tool for control, confinement, and accumulation of polarized substances: the case of MgB2

MgB2 Thick Films on Three-Dimensional Structures Fabricated by HPCVD

High-Q magnetic levitation and control of superconducting microspheres at millikelvin temperatures

Magnetic Shielding Capability of MgB2 Cup Made by Liquid Infiltration Process

Levitation force measurement and characteristics analysis of double sided high temperature superconducting thin film device

Thin Film Magnesium Boride Superconductor with Very High Critical Current Density and Enhanced Irreversibility Field

Properties of Superconducting MgB2 Spherical Shells Deposited on 2 Mm and 1 Mm Diameter Si3N4 Spheres

Improved superconducting properties of MgB2

Review of Synthesis of High Volumetric Density, Low Gravimetric Density MgB2 Bulk for Potential Magnetic Field Applications

A trapped field of 17.6 T in melt-processed, bulk Gd-Ba-Cu-O reinforced with shrink-fit steel

Permanent magnet with MgB2 bulk superconductor

In Situ Epitaxial MgB2 Thin Films for Superconducting Electronics

High transport critical currents in dense, metal-clad superconductor wires of MgB2

Enhancement of Levitation Force Characteristics in High Tc Superconducting Levitation.

Coating Thick MgB 2 Layer on Stainless Steel Substrate

Single-Ring Magnetic Levitation Configuration for Object Manipulation and Density-Based Measurement

Demonstrating levitation within a microwave cavity