Abstract:The microstructure of Al-Cu-Li alloys is influenced by the alloying contents, which in turn affect the ultimate performance. This study examined the microstructure characteristics of Al-Cu-Li alloys with varying Li contents (1.05, 1.30, and 1.66 wt.%) in as-cast state, as well as microstructure evolution during homogenization treatments. The investigation employed a range of analytical techniques, including optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), X-ray diffraction (XRD), differential scanning calorimeter (DSC), focused ion beam (FIB), transmission electron microscopy (TEM), and thermodynamic calculation software. The findings indicate that the eutectic phase exhibited significant variations with the Li content changing. Three distinct low-melting phases were identified in 1.05Li alloy, including Ag-containing Al 2 CuMg, Al 7 Cu 4 Li, and Al 2 Cu. As Li content was elevated to 1.30 wt.%, there was a noticeable drop in the quantities of Ag-containing Al 2 CuMg and Al 7 Cu 4 Li phases. Conversely, the Al 2 Cu phase increased, and a few Al 2 CuLi phases emerged. When the Li raised to 1.66 wt.%, an increased Al 2 CuLi phase was discovered, which existed along the dendritic edges. However, there were only little Ag-containing Al 2 CuMg phase, and no Al 7 Cu 4 Li phase detected. The initial melting temperatures for the four soluble eutectic phases were systematically arranged in the following order: Ag-containing Al 2 CuMg < Al 7 Cu 4 Li < Al 2 Cu < Al 2 CuLi. The elevated Li content resulted in a challenge of dissolution of the eutectic phases. Following 500°C/12h homogenization process, the containing-Ag Al 2 CuMg phase dissolved. Additionally, the Al 7 Cu 4 Li and Al 2 Cu phases were eliminated through subsequent 515°C/12h homogenization. In addition, the Al 2 CuLi phase was still existing.

Effect of Li element on shocking behavior of Fe-Li alloys

Crystal Plasticity Finite Element Simulation of High-Rate Shock Deformation Process of <100> LiF

Shock induced plasticity and phase transition in single crystal lead by molecular dynamics simulations

Effect of Li on Microstructures and Properties of Al-3.5Cu-1.5Mg Alloy

The mechanism of plasticity and phase transition in iron single crystals under cylindrically divergent shock loading

Role of micro-alloying element in dynamic deformation of Mg-Y alloys

Effects of order-disorder transition on phase relationship, elastic strength, and mechanical anisotropy of Al-Li alloys

Influence of enhanced Li content on the as-cast eutectic phase features and the evolution during homogenization of Al-Cu-Li alloys

Effect of Li Content on Properties and Microstructure Evolution of Near-Rapid Solidified 2A97 Al-Li Alloy

Effects of Li Content on Phase Evolution and Mechanical Properties of Mg-xLi-6Zn-1.5Y Alloy

Inhibiting Effect of I-phase Formation on the Plastic Instability of the Duplex Structured Mg-8Li-6Zn-1.2Y (in Wt.%) Alloy

Enhancing Plasticity in BCC Mg-Li-Al Alloys Through Controlled Precipitation at Grain Boundaries

Effects of Coarse Al2CuLi Phase on the Hot Deformation Behavior of Al–Li Alloy

The Effect Of Alloying Elements On The Structural Stability, Mechanical Properties, And Debye Temperature Of Al3li: A First-Principles Study

Dynamic precipitation and its effect on microstructure of 2195 Al–Li alloy during medium/high temperature deformation

Effect of crystallographic orientations on shock-induced plasticity for CoCrFeMnNi high-entropy alloy

Constitutive Analysis and Microstructure Characteristics of As-Homogenized 2198 Al–Li Alloy under Different Hot Compression Deformation Conditions

Effects of lattice distortion and chemical short-range ordering on the incipient behavior of Ti-based multi-principal element alloys: MD simulations and DFT calculations

A Coupled Phase-Field and Crystal Plasticity Model for Understanding Shock-Induced Phase Transition of Iron

Effect of the structure and volume fraction of nanophase on the mechanical properties of (FeNi)86B14 amorphous nanocrystalline alloys

Elemental partitioning-mediated crystalline-to-amorphous phase transformation under quasi-static deformation