Synthesis of Potassium Iodate by Electrochemical Method

Mo Bing-hui

Abstract:Potassium iodate was synthesized by electrochemical method and the extend experimentation was studied. The total yield of potassium iodate was 97.5%,the purity was 100.2%(mass fraction),and the current efficiency was 97% under the optimum process conditions. Simple technology and no pollution were the advantages of this process.

Chemistry

What problem does this paper attempt to address?

Effects of potassium iodide additive on direct electrosynthesis of potassium ferrate

He Weichun,Liu Guoqin,Cui Wei,Tang Ying

DOI: https://doi.org/10.3969/j.issn.1006-4990.2011.02.007

2011-01-01

Abstract:A new method for direct electrosynthesis of solid potassium ferrate(K2FeO4) in KOH solution using potas-sium iodide(KI) as additive was put forward.Fe electrode and K2FeO4 sample were characterized by means of CV,EDX,IR,and SEM etc..Results showed that using the additive during synthesis could result in the highest current efficiency of 76.6%,product purity of 95.3%~97.8%,and a yield of 66 g/L K2FeO4 at 65 ℃;and the current density could be enhanced from 2.5 mA/cm2 to 4.5 mA/cm2,which is 80% higher than that of the blank sample when keeping current efficiency over 63%.EDX and IR results indicated K2FeO4 sample obtained by using additive contained little iodine and appeared longer polyhedron in shape than that of the blank sample.
An Improved Method of Preparing Iridium Oxide Electrode Based on Carbonate-Melt Oxidation Mechanism

Yiwen Pan,Zhentao Sun,Hangqi He,Yifan Li,Long You,Hao Zheng

DOI: https://doi.org/10.1016/j.snb.2018.01.069

IF: 9.221

2018-01-01

Sensors and Actuators B Chemical

Abstract:pH is a fundamental parameter in understanding the chemical processes in many fields. Based on the strong oxidative characteristic of the molten lithium carbonate (Li2CO3), an advanced iridium oxide electrode preparation approach is developed by adding sodium peroxide (Na2O2) powder into a Li2CO3 melt in a semi-closed/closed reactor at a high temperature to increase the regional peroxide (O-2(2-)) ion concentration in the iridium-melt interface. The iridium oxide film (IROF) of prepared electrodes has a dense and uniform surface with small and cone-shaped particles. Open-circuit tests show that electrodes exhibit a near-Nernstian pH response with good linearity, fast response, high stability (a slight periodic fluctuation of potential change with standard deviation <0.65 mV in 48 h), good reversibility in the pH range of 2.00-10.00, and anti-interference to low concentration of oxidants. Besides, electrodes show a stable response in seawater, indicating the major ions in seawater do not influence their performances. In addition, prepared electrodes from the same batch show consistency in terms of sensitivity and the intercept of the standard curve (E degrees), while electrodes from different batches vary in E degrees, which could be attributed to the hardness in controlling identical synthetic conditions among fabrications of different batches. (C) 2018 Elsevier B.V. All rights reserved.
Potassium iodide as a low-cost cathode material for efficient potassium-ion storage

Leqing Deng,Meiying Feng,Ruiting Wang,Yusi Yang,Xiaogang Niu,Juan Zhang,Lulu Tan,Jianwen Zhang,Yifan Chen,Liang Zeng,Yujie Zhu,Lin Guo

DOI: https://doi.org/10.1016/j.ensm.2021.07.025

IF: 20.4

2021-10-01

Energy Storage Materials

Abstract:Potassium-ion batteries (KIBs) are attractive electrochemical energy storage technologies because of their low cost and high energy density. Currently, the reported cathode candidates for KIBs are all limited to the intercalation-type materials. The working principles of these materials all involve the repeated intercalation-deintercalation of bulky K-ions in the ionically-bonded rigid frameworks, which often results in sluggish reaction kinetics, irreversible structural deformation, and poor cycling stability. Here, a low-cost conversion-type material, potassium iodide (KI), is proposed as a promising cathode candidate for KIBs. It is revealed that the depotassiation-potassiation of KI proceeds via a dissolution-precipitation reaction process involving the highly soluble KI3 intermediate, leading to the shuttle effect and capacity decay. Susequently, a simple strategy combining electrolyte modulation with separator modification is adopted to effectively enhance the electrochemical performance of KI, leading to an impressive capacity retention of 95.5% after 550 cycles. The present study may shed some light on further exploration of high-performance electrode materials based on dissolution-precipitation reaction mechanism for the emerging KIBs.

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology
Active ion-exchangeable Bi2O(OH)2SO4 synthesized by ball milling for effective iodine enrichment: Insight into the pathway

Wang Chao,Hu Huimin,Chen min,Huang junwei,Peng Lei,Wang qian,Shi qing,Zhang tingting,Zhang Qiwu

DOI: https://doi.org/10.1016/j.jnucmat.2022.154081

IF: 3.555

2022-12-15

Journal of Nuclear Materials

Abstract:Effective capture of radioactive iodine and iodine enrichment from dilute source are highly desirable but still remain as significant challenges. Based on mechanochemical activation of Bi oxide (Bi2O3) toward iodine incorporation by forming BiOI, we report a new approach to functionalize Bi2O3 with several anion groups just by simply co-milling with Bi sulfate. Several analytical methods were used to characterize the reaction products and its high efficiency for iodine enrichment inside. Compared with activation just for α-Bi2O3 itself, formation of Bi2O(OH)2SO4 was confirmed to allow a tremendous increase in adsorption capacity up to 335.57 mg/g towards iodine with the product, due to effect by ion-exchange with three anion groups (SO42−, CO32−, OH−) to form BiOI with a stable structure of Bi-O layer, demonstrating obvious advantages as a newly developed typical anionic adsorbent. Iodine can be recovered by heating BiOI to give back Bi2O3 for recycling. As a cost-effective and environmental-friendly process to produce an efficient material for iodine enrichment, this research may open a promising way to effectively remove radioactive iodine and recover iodine resources.

materials science, multidisciplinary,nuclear science & technology
Understanding the Synthesis of Inorganic Solid-State Electrolytes for Li Ion Batteries: Features and Progress

Shu Zhao,Wei Jiang,Xinxin Zhu,Min Ling,Chengdu Liang

DOI: https://doi.org/10.1016/j.susmat.2022.e00491

IF: 10.681

2022-01-01

Sustainable Materials and Technologies

Abstract:Inorganic solid electrolytes (ISEs) have recently attracted tremendous research interest because of their excellent thermal stability and nonflammability. The synthesis methods influence ISEs in the aspect of phase structure, ratio of amorphous phases, strain, defects, grain size, grain boundary resistance, impurities, and morphology, thus critically determining their performance in batteries. However, the relation between the synthesis of ISEs and their performance is complicated and there is no widely applicable synthesis method for all ISEs. To guide those who are deciding on synthesis methods for ISEs, a broad survey is reported in this review. The mechanisms of these synthesis methods are illustrated. Their advantages and disadvantages are sorted. Novel methods up to date, which can intrigue new ideas are also introduced based on our insights into the ISEs.
Effects of KIO 3 Additive on the Direct Electrosynthesis of K 2 FeO 4

Weichun He,Guoqin Liu,Wei Cui,Ying Tang

DOI: https://doi.org/10.1134/s1023193511110097

2011-01-01

Russian Journal of Electrochemistry

Abstract:An electrosynthesis in 14.5 M KOH electrolyte using KIO3 additive is presented for the direct synthesis of solid K2FeO4, with a highest efficiency of 77.6%, purities of 95.3–97.8% and a yield of 68 g l−1 K2FeO4 at 65°C. The results show that using the additive during synthesis of ferrate(VI) can increase the current efficiency by 26% than the blank in degree. Its function is similar to the results of using ultrasonic. The techniques of CV, EDX, IR, SEM and XRD are used to feature the Fe electrode or K2FeO4 samples. It is found that addition of KIO3 can increase the potential of oxygen evolution on the CV of Fe anode in KOH significantly. The EDX measurement displays that K2FeO4 sample obtained using KIO3 additive contains no iodine. The sample exhibits similar IR feature absorption spectra and XRD patterns but some dissimilar crystal morphologies to the one with blank.
Modeling of Potassium Sulfate Production from Potassium Chloride by Electrodialytic Ion Substitution

Xiaoyao Wang,Xiaozhao Han,Xu Zhang,Quhua Li,Tongwen Xu

DOI: https://doi.org/10.1021/acssuschemeng.7b01992

IF: 8.4

2017-01-01

ACS Sustainable Chemistry & Engineering

Abstract:An experimental study was carried out on the preparation of potassium sulfate from potassium chloride by electrodialytic ion substitution. Effects of sulfate species, current density, and molar ratio of ammonium sulfate to potassium chloride were investigated. Results showed that ammonium sulfate was regarded as the optimum sulfate source because of the lowest energy consumption and cheap raw materials. When current density was set as 20 or 30 mA/cm(2), the generated products can conform to the Chinese Government standard (GB20406-2006). A higher molar ratio can promote the substitution reaction more completely but results in larger loss of K+ ions and more increment of NH4+ ions in products. Moreover, a mathematical model was established to predict the product concentration. Results showed that there is a good agreement between experimental and computational concentrations.
Efficient capture and stabilization of iodine via gas-solid reaction using cyclodextrin metal-organic frameworks

Jiacai Chen,Tao Guo,Xiaohong Ren,Ting Yang,Kaikai Zhang,Yuhua Guo,Xiaojin Chen,Shuangying Gui,Shujun Wang,Qianqian Li,Can Peng,Jiwen Zhang,Li Wu

DOI: https://doi.org/10.1016/j.carbpol.2022.119507

IF: 10.723

2022-09-01

Carbohydrate Polymers

Abstract:For treatment of wound infection with stabilized iodine, potassium iodide cyclodextrin metal-organic frameworks (KI-CD-MOF) was prepared to carry iodine via gas-solid reaction. Apart from highly ordered porous frameworks, KI-CD-MOF contains uniformly distributed iodide ions which stabilize iodine (I2). X-ray photoelectron spectroscopy and potentiometric titration were utilized to confirm the formation of I3− in the highly porous KI-CD-MOF as I2@KI-CD-MOF. Molecular simulation and characterizations of the synchrotron radiation Fourier transform infrared spectroscopy, differential scanning calorimeter, powder X-ray diffraction and N2 adsorption were conducted to illustrate the inclusion mechanism of iodine in I2@KI-CD-MOF. The apparent solubility of iodine in water was 3.86 times enhanced. The stability and antibacterial activity tests demonstrated that the highly-dispersed iodide ions in KI-CD-MOF are crucial in improvement to the solubility, stability, and bacteriostatic effects of active iodide. Therefore, KI-CD-MOF has broad application prospects and advantages in efficiently capturing and stabilizing iodine.

polymer science,chemistry, organic, applied
Conversion of Potassium Chloride into Potassium Sulfate by Four-Compartment Electrodialysis: Batch Operation Process

Xu Zhang,Xiaoyao Wang,Xianchao Liu,Xiaozhao Han,Chenxiao Jiang,Qiuhua Li,Tongwen Xu

DOI: https://doi.org/10.1021/acs.iecr.5b03245

2015-01-01

Industrial & Engineering Chemistry Research

Abstract:K2SO4 is a kind of potassic fertilizer, which is mainly prepared through converting KCl with dissolved sulfate or H2SO4. In this study, four-compartment electrodialysis was used to convert KCl with (NH4)2SO4 into K2SO4 to overcome the shortcomings of traditional methods. The phase of product crystals was identified by XRD and the crystal composition was determined by the ion content. Economic evaluation was conducted, and the effects of operation variables on conversion performance were investigated. Results showed that as current density increases from 10 to 25 mA/cm2, operation time decreases from 135 to 55 min while energy consumption increases from 0.26 to 0.50 kw·h/kg K2SO4. A slightly higher than theoretical molar ratio of (NH4)2SO4 to KCl can ensure the complete conversion of KCl into K2SO4. In addition, final K2SO4 concentrations could be increased by reducing the initial K2SO4 tank volume. Finally, higher temperature is beneficial for conversion performance and subsequent evaporation crystallization.
Potassium Manganese Oxides:Electrochemically Controlled Synthesis and Capacitor Properties

FENG Liang-Dong,Jianjun Shi,JIANG Li-Ping,Junjie Zhu

2010-01-01

Chinese journal of inorganic chemistry

Abstract:Potassium manganese oxides were prepared by cathodic deposition from aqueous KMnO4 solution on an indium tin oxide slide. The products were characterized by XRD, XPS and SEM techniques. The as-prepared products were potassium manganese oxides with different manganese valence states. The component, morphology and size of the products could be controlled through adjusting the preparation parameters such as deposition potential, deposition time and acidity of the electrolyte. The results show that the deposition of potassium manganese oxide from aqueous KMnO4 is a pH value dependent procedure. Due to the facilitating of intercalation and deintercalation of cations, the specific capacitance of the products deposited for 500 s is higher than that of 3 000 and 6 000 s. At a scan rate of 2 mV . s(-1) in 0.2 mol . L-1 K2SO4 aqueous electrolyte, the specific capacitances of products are 119.4, 99.5 and 109.0 F . g(-1) corresponding to the deposition time of 500, 3 000 and 6 000 s, respectively. Electrochemical experiments indicate that the reversibility and performance of these potassium manganese oxides are also changed with the deposition time.
The Combined First Principles and Experimental Study of O-doped KMnF3 As a Cathode for Potassium-Ion Batteries

Shuya Wang,Yaxin Chen,Bin Cui,Bo Li,Shuxuan Wang,Yanhua Cui,Zhicheng Ju,Quanchao Zhuang

DOI: https://doi.org/10.1016/j.apsusc.2020.145954

IF: 6.7

2020-01-01

Applied Surface Science

Abstract:Computer simulation accelerates the selection and application of new electrode materials. The First-principles calculations based on density functional theory (DFT) are performed to evaluate the performance as cathode for Potassium ion batteries (PIBs) on the structure, electronic conductivity and ionic diffusion of O-doped KMnF3. After taking comprehensive consideration of the calculation results, the nanostructured O-doped KMnF3 was synthesized and the structure and electrochemical properties were further improved by carbon coating. Here, we report a new etch pathway to create a new class of carbon-coated perovskite fluoride to improve the performance of PIB in terms of rate capability and cycle stability. These new material design concepts will help discover and synthesize new materials for PIBs.
Novel KOH electrolyte for one-step electrochemical synthesis of high purity solid K2FeO4: Comparison with NaOH

Weichun He,Jianming Wang,Haibo Shao,Jianqing Zhang,Chu-nan Cao

DOI: https://doi.org/10.1016/j.elecom.2005.04.011

IF: 5.443

2005-01-01

Electrochemistry Communications

Abstract:An electrosynthesis from an iron wire gauze in KOH electrolyte is first presented for the in situ direct synthesis of the solid K2FeO4, with a highest efficiency of 73.2%, purities of 95.3–98.1% and a highest yield of 49gl−1 K2FeO4 at 65°C, which is far better than that in NaOH electrolyte as a whole. A variety of electrolysis conditions including cell configuration, applied current density, temperature and electrolyte concentration have been explored. The in situ and ex situ electrochemically directly synthesized K2FeO4 powders exhibit similar IR absorption spectra and XRD patterns to the chemical synthesized K2FeO4 but different crystal morphologies.
Electrolyte Solvation Structure Manipulation and Synthetic Optimization for Enhanced Potassium Storage of Tin Phosphide/Carbon Alloy-Based Electrode

Zhen Feng,Ruoxuan Chen,Rui Huang,Fangli Zhang,Weizhen Liu,Sailin Liu

DOI: https://doi.org/10.3390/met13040658

IF: 2.695

2023-03-27

Metals

Abstract:Phosphorus-based materials are considered to be reliable anode materials for potassium ion batteries (PIBs) due to their high theoretical capacity but suffer from inferior cycling stability and an unstable Solid Electrolyte Interface (SEI) layer. Herein, optimized ball-milled parameters and concentrated electrolytes are introduced to enhance the electrochemical performance of Sn4P3/C anodes. Consequently, the electrodes synthesized under optimized ball milling parameters could deliver a reversible capacity of 307.8 mA h g−1 in diluted Potassium hexafluorophosphate (KPF6) electrolyte. Moreover, compared with diluted bis(fluorosulfonyl)imide (KFSI) electrolyte, a robust inorganic KF-rich SEI layer can be formed on the electrode's surface by employing concentrated KFSI electrolyte and provides more rapid K ion conduction rates. Meanwhile, a large proportion of the FSI− anions participated in the K+ solvation shell when the KFSI concentration increased. As a result, high specific capacities (225.1 mA h g−1 at 50 mA g−1 after 200 cycles) and excellent Coulombic efficiency (97.24% at 500 mA g−1 after 200 cycles) can be achieved. This work may deepen our understanding of synthetic optimization in electrode material design and the role of concentrated electrolyte in tunning the solvation structure, and also offer an insightful clue to the design of high-capacity phosphorus-based anodes.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Clean Production Technology of Potassium Ferrate by Chemical Oxidation

Hong Jiang

2001-01-01

Abstract:Potassium ferrate was preparated from chlorine,potassium hydroxide and ferric nitrate by chemical oxidation.The effects of reagent concentration,reaction temperature,and etc.on yield of potassium ferrate were studied.The optimal conditions were as follows: oxidation under 20℃ for 30 min with Fe(Ⅲ) dosage of 90% stoichiometric amount; precipitation under 15～20 ℃ for 30 min.The final product was rinsed and refined with normal pentane,ethanol and ether successively under -5℃.
Novel Attapulgite/Polyaniline/Phosphomolybdic Acid-Based Modified Electrode for the Electrochemical Determination of Iodate

Susu Zhang,Ping He,Wen Lei,Guangli Zhang

DOI: https://doi.org/10.1016/j.jelechem.2014.04.011

IF: 4.598

2014-01-01

Journal of Electroanalytical Chemistry

Abstract:A novel attapulgite/polyaniline/phosphomolybdic acid-based amperometric sensing platform was constructed for the determination of iodate. Nanostructured attapulgite was utilized for reducing agglomeration of polyaniline particles, and the as prepared attapulgite/polyaniline composite was used to immobilize phosphomolybdic acid. Excellent electrocatalytic performance was obtained due to the synergistic effect of nanostructured attapulgite, polyaniline and phosphomolybdic acid. The electrochemical responses of as prepared modified electrode were investigated by cyclic voltammetry and chronoamperometry. The modified electrode exhibited linear amperometric response for iodate in the concentration range of 2.0 x 10(-6) M-5.2 x 10(-4) M (R = 0.999). The detection limit was calculated as 53 x 10(-7) M. Good reproducibility, high stability, fast amperometric response, and possibility of rapid preparation were also great advantages of this modified electrode. Based on this work, the attapulgite/polyaniline/phosphomolybdic acid modified electrode was successfully applied to determine iodate in a commercial table salt sample. (C) 2014 Elsevier B.V. All rights reserved.
One-pot preparation of Potassium, Iodine-Codoped Hydrophilic Polymeric Carbon Nitride with Highly Efficient Quasi-Homogeneous Photocatalytic H 2 O 2 Production

Dan Zheng,Yaorong Su,Da Wen,Zheng Zhang,Peiyi Yang,Xinyuan Ma,Yewang Chen,Liwei Deng,Shuang Zhou,Aiyun Meng

DOI: https://doi.org/10.1016/j.jcat.2023.115180

IF: 7.3

2023-10-27

Journal of Catalysis

Abstract:The production of hydrogen peroxide (H 2 O 2 ) through visible photocatalytic molecular oxygen has gained significant attention as an environmentally friendly and sustainable approach. In this study, a unique multivariate modified graphitic carbon nitride (g-C 3 N 4 ) photocatalyst is designed and successfully synthesized by incorporating K and I species as heteroatomic co-dopant, along with the defect engineering in g-C 3 N 4 . The resulting photocatalyst consists of particles ranging in size from 50 to 200 nm. Experimental results reveal that K atoms form chemical bonds with N atoms in adjacent layers, facilitating enhanced electron migration. On the other hand, I atoms predominantly localize at the edges of g-C 3 N 4 building blocks, contributing to the formation of cyano groups (-C≡N). These cyano groups, acting as nitrogen defects, can effectively narrow the band gap, elevate the conduction band, and effectively improve the generation and transport of photoexcited charge carriers. By precisely controlling the proportion of KI, the formation of cyanide can be effectively regulated. Notably, the obtained photocatalyst exhibits a remarkably high H 2 O 2 yield of 4386.4 μΜ h −1 under visible light, surpassing that of g-C 3 N 4 and other g-C 3 N 4 -based photocatalysts. This work presents a novel design strategy for the development of highly efficient photocatalysts for H 2 O 2 production.

chemistry, physical,engineering, chemical
Synthesis, Structural Analysis, and Degradation Behaviour of Potassium Tin Chloride as Chloride-Ion Batteries Conversion Electrode Material

Soutam Panja,Yidong Miao,Johannes Döhn,Jaehoon Choi,Simon Fleischmann,Shivaraju Guddehalli Chandrappa,Thomas Diemant,Axel Groß,Guruprakash Karkera,Maximilian Fichtner

DOI: https://doi.org/10.26434/chemrxiv-2024-wqvw0

2024-08-12

Abstract:Chloride ion batteries (CIBs) offer a compelling alternative to lithium-ion systems, particularly in applications demanding cost-effectiveness and resource sustainability. However, the development of tailored electrode materials remains a critical bottleneck for CIB advancement. In this study, we synthesized an untapped class of perovskite-based material potassium hexachlorostannate (K2SnCl6, denoted as KSC) via a facile mechanochemical route for the first time. The prepared KSC was subjected to various characterization techniques to confirm its crystal structure and morphology. Herein, KSC exhibited intriguing electrochemical performance in a non-aqueous CIB configuration, utilizing a lithium metal counter electrode. Furthermore, ex-situ X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analysis, reveal a conversion reaction mechanism involving chloride ion shuttling and provide insights into structural evolution during cycling. Moreover, the Density functional theory (DFT) studies supported additional degradation products that could potentially limit the performance of these materials, limiting the performance of these materials as potential battery electrodes in CIBs.

Chemistry
A Cost-Effective Co-precipitation Method for Synthesizing Indium Tin Oxide Nanoparticles Without Chlorine Contamination

Haiwen Wang,Xiujuan Xu,Jianrong Zhang,Chunzhong Li

DOI: https://doi.org/10.1016/s1005-0302(10)60171-5

2010-01-01

Abstract:Indium tin oxide (ITO) nanoparticles with crystallite size of 12.6 nm and specific surface area of 45.7 m(2).g(-1) were synthesized by co-precipitation method. The indium solution was obtained by dissolving metal indium in HNO3. The tin solution was obtained by dissolving metal tin in HNO3 and followed by stabilizing with citric acid. The free of chlorine ions in the synthesis process brought several advantages: shortening the synthesis time, decreasing the particle agglomeration, decreasing the chlorine content in the ITO nanoparticles and improving the particle sinterability. This is the first time to report the synthesis of ITO nanoparticles free from chlorine contamination without using the expensive metal alkoxides as starting materials.
Synthesis, Structural Analysis, and Degradation Behavior of Potassium Tin Chloride as Chloride‐Ion Batteries Conversion Electrode Material

Soutam Panja,Yidong Miao,Johannes Döhn,Jaehoon Choi,Simon Fleischmann,Shivaraju Guddehalli Chandrappa,Thomas Diemant,Axel Groß,Guruprakash Karkera,Maximilian Fichtner

DOI: https://doi.org/10.1002/adfm.202413489

IF: 19

2024-09-11

Advanced Functional Materials

Abstract:Novel perovskite‐based K2SnCl6 is synthesized via mechanochemical synthesis for chloride–ion batteries (CIBs) shows promising electrochemical performance via chloride ion shuttling. Ex situ characterizations and DFT studies reveal conversion reaction mechanisms and potential degradation products limiting its performance in an electrochemical environment. Chloride–ion batteries (CIBs) offer a compelling alternative to conventional battery systems, particularly in applications demanding cost‐effectiveness and resource sustainability. However, the development of tailored electrode materials remains a critical bottleneck for CIB advancement. In this study, an untapped class of perovskite‐based material, potassium hexachlorostannate (K2SnCl6, denoted as KSC) is synthesized via a facile mechanochemical route for the first time. The prepared KSC is subjected to various characterization techniques to confirm its crystal structure and morphology. Herein, KSC exhibits intriguing electrochemical performance in a non‐aqueous CIB configuration, utilizing a lithium metal counter electrode. Furthermore, ex situ X‐ray diffraction (XRD) and X‐ray photoelectron spectroscopy (XPS) analysis, reveal a conversion reaction mechanism involving chloride ion shuttling and provide insights into structural evolution during cycling. Moreover, the density functional theory (DFT) studies support additional degradation products that can potentially limit the performance of these materials as potential battery electrodes in CIBs.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Electrochemical Preparation, Characterization and Discharge Performance of Solid K3Na(FeO4)2

Weichun He,Jianming Wang,Yukai Fan,Zhihua Xu,Jianqing Zhang,Chu-nan Cao

DOI: https://doi.org/10.1016/j.elecom.2006.09.012

IF: 5.443

2006-01-01

Electrochemistry Communications

Abstract:An electrosynthesis from an iron wire gauze in concentrated NaOH electrolyte is first presented for the synthesis of 0.82 M Na2FeO4 solution, and then for the synthesis of solid K3Na(FeO4)(2) with purities of 95.3-97.5% and a highest yield of 95%. The synthesis conditions have been explored. The EDX, AAS, FTIR, XRD and electrochemical measurements have been used to characterize the obtained solid sample. Different from K2FeO4 crystals, the synthesized K3Na(FeO4)(2) powders exhibit three characteristic IR absorption peaks (787, 801-802 and 858-862 cm(-1)) and a hexagonal unit cell with the space group P3ml (164). The results of electrochemical experiments show that the K3Na(FeO4)(2) electrode has slightly better discharge performance than K2FeO4 one at relatively high discharge currents. (c) 2006 Elsevier B.V. All rights reserved.

Synthesis of Potassium Iodate by Electrochemical Method

Effects of potassium iodide additive on direct electrosynthesis of potassium ferrate

An Improved Method of Preparing Iridium Oxide Electrode Based on Carbonate-Melt Oxidation Mechanism

Potassium iodide as a low-cost cathode material for efficient potassium-ion storage

Active ion-exchangeable Bi2O(OH)2SO4 synthesized by ball milling for effective iodine enrichment: Insight into the pathway

Understanding the Synthesis of Inorganic Solid-State Electrolytes for Li Ion Batteries: Features and Progress

Effects of KIO 3 Additive on the Direct Electrosynthesis of K 2 FeO 4

Modeling of Potassium Sulfate Production from Potassium Chloride by Electrodialytic Ion Substitution

Efficient capture and stabilization of iodine via gas-solid reaction using cyclodextrin metal-organic frameworks

Conversion of Potassium Chloride into Potassium Sulfate by Four-Compartment Electrodialysis: Batch Operation Process

Potassium Manganese Oxides:Electrochemically Controlled Synthesis and Capacitor Properties

The Combined First Principles and Experimental Study of O-doped KMnF3 As a Cathode for Potassium-Ion Batteries

Novel KOH electrolyte for one-step electrochemical synthesis of high purity solid K2FeO4: Comparison with NaOH

Electrolyte Solvation Structure Manipulation and Synthetic Optimization for Enhanced Potassium Storage of Tin Phosphide/Carbon Alloy-Based Electrode

Clean Production Technology of Potassium Ferrate by Chemical Oxidation

Novel Attapulgite/Polyaniline/Phosphomolybdic Acid-Based Modified Electrode for the Electrochemical Determination of Iodate

One-pot preparation of Potassium, Iodine-Codoped Hydrophilic Polymeric Carbon Nitride with Highly Efficient Quasi-Homogeneous Photocatalytic H 2 O 2 Production

Synthesis, Structural Analysis, and Degradation Behaviour of Potassium Tin Chloride as Chloride-Ion Batteries Conversion Electrode Material

A Cost-Effective Co-precipitation Method for Synthesizing Indium Tin Oxide Nanoparticles Without Chlorine Contamination

Synthesis, Structural Analysis, and Degradation Behavior of Potassium Tin Chloride as Chloride‐Ion Batteries Conversion Electrode Material

Electrochemical Preparation, Characterization and Discharge Performance of Solid K3Na(FeO4)2