Abstract:Single hat sectioned hybrid beams composed of aluminum and Carbon Fiber Reinforced Polymeric materials (CFRP), intended for structural applications in the automotive and aviation sectors, have been studied from the point of their energy absorption capabilities when submitted to transverse low-velocity impact loading. Carbon fiber-epoxy composite prepregs were placed on the inside of the single hat sectioned aluminum sheet and completely cured in the autoclave under the recommended curing cycle. The bonding process between the aluminum sheet and composite layers was achieved by using 3M VHB™ 4930 double-sided acrylic foam tape. Bonding the aluminum and composite layers through adhesive tape eliminates the requirement of surface preparation of the aluminum layer through chemical etching or mechanical abrasion and thereby the strength of the metallic layer is not reduced due to the formation micropores during the chemical etching process. Results are shown in terms of load-displacement and damage morphologies diagrams; characteristic trends are compared and discussed. It was observed that the presence of viscoelastic adhesive tape material restricts the rupture (visual cracks) failure of the outer aluminum layer, resulting in the only impact-induced indentation for all impact energies. Numerical simulations were also performed to characterize and predict the failure mechanism of such hybrid beams when subjected to impact loading. Numerical predictions showed good correlation with experimental results for all impact histories at low and medium impact energies but a showed slight discrepancy for highest impact energy and were not able to successfully capture the system response in the unloading region. Current modeling does not consider damage healing or recovery with unloading and it is difficult to account for such change in material state. This study provides the low-velocity impact characteristics and collapse behavior of the hybrid hat sectioned beams under tensile and shear forces developed by impact loading by providing insight to their primary damage mechanisms relative to the impact energies. It was found that the primary damage of the specimen's changes from impact-induced indentation, minimal fiber breakage to partial perforation accompanied by larger indentation depth as the impact energy is increased from 6 to 12 J.

High-Velocity Impact Damage Assessment of Aluminum-Honeycomb-Cored Banana-Fiber-Reinforced Composite Structures Under Elevated Temperatures

High-temperature High-Velocity Impact on Honeycomb Sandwich Panels

Experimental Study on Damage Characteristics of CFRPs/Aluminum Honeycomb Sandwich Structure Impacted by Ultra-High Speed Under High and Low Temperatures

Impact behaviors of sandwich wall panels at elevated temperatures

Transverse impacts‐induced deformation and damage of 3D angle‐interlock woven composites at elevated temperatures

High Velocity Impact Response of Composite Lattice Core Sandwich Structures

A Computational Analysis of the High-velocity Impact Performance of Lightweight 3D Hybrid Composite Armors

Structural response of sandwich structures with CFRP face sheets under quasi-static indentation and high velocity impact: An experimental and numerical study

Low-Velocity Impact Characteristics of Hybrid Aluminum/CFRP Single Hat Sectioned Beam Adhesively Bonded Using Adhesive Tape

High velocity impact tests on high temperature carbon-carbon composites ☆

High-temperature Damage Tolerance of Carbon Fibre-Reinforced Plastics

A comprehensive study of low-velocity impact behavior and damage evaluation of angle-ply thin woven GFRP composites under various temperatures

Perforation of Needle-Punched Carbon-Carbon Composites During High-Temperature and High-Velocity Ballistic Impacts

Effect of high-temperature environment on the penetration resistance characteristics of carbon fiber/bismaleimide composite laminates

The behaviour of thermoplastic and thermoset carbon fibre composites subjected to low-velocity and high-velocity impact

Damage characterization of sandwich composites subjected to impact loading

Investigation of the Effects of Core Thickness on Low Velocity Impact Behaviors of Aluminum Honeycomb Composites

Low velocity impact and pseudo-ductile behaviour of carbon/glass/epoxy and carbon/glass/PMMA hybrid composite laminates for aircraft application at service temperature

Influence of Temperature on the Impact Behavior of Woven-Ply Carbon Fiber Reinforced Thermoplastic Composites

Low-velocity impact and quasi-static post-impact compression analysis of woven structural composites for automotive: Influence of fibre types and architectural structures

Investigation of low velocity impact behaviors of honeycomb sandwich composites