Abstract:High manganese steels containing 15%—30%(mass fractions) Mn and additions of(2%—4%)Si and(2%—4%)A1 exhibit superior ductility and extraordinary strengthening behavior during plastic deformation,due to extensive twin formation under mechanical load(the so-called TWIP effect-twinning induced plasticity effect) or thee-martensite andα'-martensite transformation(the so- called TRIP effect-transformation induced plasticity effect).In this paper,different heat treatments were carried out for high-manganese TRIP steels of Fe-15Mn-4Si-2Al and Fe-20Mn-4Si-2Al,and the uniaxial tensile tests were performed.The results show that increase of holding time at 1373 K can increase elongation and strength.Through the analysis of stress-strain curves,the relationship between mechanical properties and deformation mechanism was established.The dependence of phase compositions in high manganese TRIP steels on the heat treatment parameters has been studied by metallographic characterization and XRD pattern.The transformation routes ofγ→e→α' andγ→α' were observed by TEM,which dominates the TRIP effects.Microstructural characterization ofe-martensite andα'-martensite indicated thatα'-martensite held the K-S orientation relationship with austenite,and the S-N(Shoji-Nishiyama) orientation relationship was observed between austenite ande-martensite,wherease-martensite andα'-martensite held the Burgers orientation relationship. Deformation behavior of the two kinds of high Mn steels has been clarified through the relationship between work hardening rate of dσ/deand true strain based on the true stress-true stain curves.It has been found that continuous transformation from austenite ore-martensite toα'-martensite can take place during deformation,which increases the work-hardening rate to improve the TRIP effect.

Enhancing ductility of the TRIP aided bainitic ferrite steel by Mn heterogeneity introduced via reversion: Towards the 3rd generation

Enhanced stretch flangeability and crack propagation behavior of an 1100 MPa grade TRIP-aided bainitic ferrite steel

A New Effect of Retained Austenite on Ductility Enhancement in High Strength Bainitic Steel

Enhancing Strength and Plasticity Synergy in Transformation-Induced Plasticity-Aided Lean Duplex Stainless Steel Based on the Ultrafine-Grained Austenite

Tailoring microstructure evolution and austenite stability of TRIP steels by Rare-Earth micro-alloying

The Role of Microstructural Constituents on Strength–Ductility–Local Formability of a Transformation‐Induced‐Plasticity‐Aided Bainitic Steel

Constructing multi-scale retained austenite makes bainitic steel better mechanical properties by introducing weak chemical heterogeneity

Characterization and 3D finite element modelling of TRIP effect in a medium manganese steel with nano-precipitates

Towards Strength-Ductility Synergy in a Medium Mn Steel Through Developing Heterogeneous Dual-Morphology Microstructure

Experimental Investigation on a Novel Medium Mn Steel Combining Transformation-Induced Plasticity and Twinning-Induced Plasticity Effects

Bainite Transformation and TRIP Effect in 20mn2sivb Steel

Enhancing strength–ductility synergy in medium Mn steel with hetero-structured austenite developed by two-stage cyclic thermomechanical treatment and flash annealing

Optimizing strength & ductility combination of medium-carbon TRIP steel via multi-stage work hardening

The Mechanism Of Ductility Enhancement By Retained Austenite In High Strength Steels

Tailoring hetero-grained austenite via a cyclic thermomechanical process for achieving ultrahigh strength-ductility in medium-Mn steel

Enhancing Both Strength and Ductility of Low-Alloy Transformation-Induced Plasticity Steel Via Hierarchical Lamellar Structure

A Phenomenon of Strain Induced Bainitic Transformation and Its Effect on Strength Enhancement in a Lightweight Transformation-Induced-plasticity Steel

MARTENSITIC TRANSFORMATION INDUCED BY DEFORMATION AND WORK-HARDENING BEHAVIOR OF HIGH MANGANESE TRIP STEELS

A Simultaneously Improved Strength and Ductility on Medium Mn TRIP Steel Designed by Pre-Twinning Strategy Based on SFE Controlling

Microstructure Evolution and Mechanical Behavior of A Hot-Rolled High-Manganese Dual-Phase Transformation-Induced Plasticity/Twinning-Induced Plasticity Steel

Study of the Influence of Δ-Ferrite on the TRIP Effect of a Low-Density High Aluminum Steel by Using Full-Field Crystal Plasticity Modeling