Abstract:The 6××× series aluminum alloys Al-Mg-Si-Cu are widely used in the transportation and building industries due to their comprehensive mechanical properties, adequate formability, high corrosion resistance and good weldability. For decades, ultrafine grain structure (UFG) produced by severe plastic deformation (SPD) has been proved to be a promising way in strengthening Al alloy materials. Although this method can guarantee a great improvement in strength, the obtained ductility is always disappointing. Besides, this method has a limitation to fabricate products suitable for practical use. Recently, combining deformation and aging has been proposed to pro-duce high-strength Al alloys. This strategy is very effective in achieving Al alloys with strength-ductility synergy even through conventional producing process, for example, rolling and aging. The strain ratio of deformation is crit-ical in tuning the mechanical properties which could be acquired by the above method. The effect of deformation strain ratio on the age-hardening behaviors and microstructure in Al-Mg-Si-Cu alloy produced by combining cold-rolling and aging are investigated using hardness test, tensile test, EBSD and TEM in this work. The results show that the as-rolled hardness increases gradually with deformation strain ratio. The age-hardening potential declines with the increase of strain ratio, though post-aging could further strengthen the as-rolled alloys. The grains elongate along the rolling direction during deformation and finally have a lamellar structure. Fragmentation and extensive defects like sub-grain boundaries occurs inside the grains. The dislocations become denser inside the alloy with the increase of the deformation ratio. When the deformation ratio is large (above 60%), formation of dislocation tan-gling and sub-grains are observed. Deformation-induced change of the dislocation configuration affects the precipitation significantly. Due to the interaction between solutes precipitation and defects annihilation, the distribution of precipitates undergoes a change from being isolated to a continuous manner.

Synergy effect of Si addition and pre-straining on microstructure and properties of Al–Cu–Mg alloys with a medium Cu/Mg ratio

EFFECT OF PRE-DEFORMATION ON AGE- HARDENING AND MICROSTRUCTURE IN Al-Mg-Si-Cu ALLOY

Study on properties and precipitation behavior of 6000 series alloys with high Mg/Si ratios and Cu contents

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

The Combined Effect of Pre-Aging and Sn Addition on Age Hardening Response and Precipitation Behavior of Al-1.0Mg-0.6Si (−0.3cu) Alloy

Effect of In addition on the precipitation behavior and mechanical property for Al-Mg-Si alloys

Synergic effect of hot deformation temperature and pre-straining on ageing precipitates and mechanical property of 2014 Al alloy

Effect of Cu addition on precipitation and age-hardening response of an Al-15%Mg2Si alloy

Sn-Sc microalloying-induced property improvement and micromechanisms of an Al-Mg-Si alloy

Effect of the Solid Solution and Aging Treatment on the Mechanical Properties and Microstructure of a Novel Al-Mg-Si Alloy

The effect of Si addition on the microstructure and tensile properties of casting Al-5.0Cu-0.6Mn-1.2Fe alloys

Influence of Li addition on mechanical property and aging precipitation behavior of Al-3.5Cu-1.5Mg alloy

Effects of Si addition on mechanical, electrical and magnetic property of Cu-10Fe alloy

The combined effect of pre-aging and Mg/Si ratio on the natural aging and bake hardening in Al-Mg-Si-0.7Cu alloys

Synergistical Effects of Mg Microalloying, Deformation, and Aging on the Strength and Electrical Conductivity of Cu‐3.3 wt%Ti Alloy

Effect of combined addition of Ag and Cu on the precipitation behavior for an Al-Mg-Si alloy

Microstructure and mechanical properties of Al-Mg-Si alloy during solution heat treatment and forging integrated forming process

Investigating the role of Cu, Zr and V on the evolution of microstructure and properties of Al-Si-Mg cast alloys

Achieving excellent strength-ductility in Al–Si–Cu–Mg cast alloy via effective work hardening

Precipitates evolution and strengthening of Al–Mg2Si alloys containing high-Cu contents during ageing process

Effect of a Trace Addition of Sn on the Aging Behavior of Al–Mg–Si Alloy with a Different Mg/Si Ratio