Abstract:Abstract Precisely constraining the source parameters of large earthquakes is one of the primary objectives of seismology. However, the quality of the results relies on the quality of synthetic earth response. Although earth structure is laterally heterogeneous, particularly at shallow depth, most earthquake source studies at the global scale rely on the Green's functions calculated with radially symmetric (1D) earth structure. To avoid the impact of inaccurate Green's functions, these conventional source studies use a limited set of seismic phases, such as long period seismic waves, broadband P and S waves in teleseismic distances (30 degrees < ∆ < 90 degrees), and strong ground motion records at close-fault stations. The enriched information embedded in the broadband seismograms recorded by global and regional networks is largely ignored, limiting the spatiotemporal resolution. Here we calculate 3D strain Green's functions at 30 GSN stations for source regions of 10 selected global earthquakes, with frequency up to 67 mill hertz (15 s), using SPECFEM3D_GLOBE and the reciprocity theorem. The 3D SEM mesh model is composed of mantle model S40RTS, crustal model CRUST2.0, and surface topography ETOPO2. We surround each target event with grids in horizontal spacing of 5 km and vertical spacing of 2.0∼3.0 km, allowing us to investigate not only the mainshock but also the background seismicity. In total, the response at over 210,000 source points is calculated in simulation. The number of earthquakes, including different focal mechanisms, centroid depth range, and tectonic background, could further increase without additional computational cost if they were properly selected to avoid overloading individual CPUs. The storage requirement can be reduced by two orders of magnitude if the output strain Green's functions are stored for periods over 15 s. We quantitatively evaluate the quality of these 3D synthetic seismograms, which are frequency and phase dependent, for each source region using nearby aftershocks, before using them to constrain the focal mechanisms and slip distribution. Case studies show that using a 3D earth model significantly improves the waveform similarity, agreement in amplitude and arrival time of seismic phases with the observations. The limitations of current 3D models are still notable, dependent on seismic phases and frequency range. The 3D synthetic seismograms cannot well match the high frequency (>40mHz) S wave and (>20mHz) Rayleigh wave yet. Though the mean time-shifts are close to zero, the standard deviations are notable. Careful calibration using the records of nearby better located earthquakes is still recommended to take full advantage of better waveform similarity due to the use of 3D models. Our results indicate that it is now feasible to systematically study global large earthquakes using full 3D earth response in a global scale.

On comparison of simulated and observed seismicity

Improvement of Source Spectrum Fall‐Off for Simulating Ground Motion Using Stochastic Green’s Function Method

Physics-based Earthquake Simulations of the Anninghe-Zemuhe-Daliangshan-Xiaojiang Fault System in Southwestern China

Calibration of Rockmass Failure Criteria for Mines Using Seismic Monitoring Data

Machine learning opportunities to conduct high-fidelity earthquake simulations in multi-scale heterogeneous geology

Numerical Simulation Study on Microseismic Characteristics and Rockburst Hazard Prediction in Deep Mining of Steeply Inclined Coal Seams

COMPARISON ON ARTIFICIAL BOUNDARIES AND SEISMIC WAVE INPUT METHODS IN SEISMIC ANALYSIS OF UNDERGROUND STRUCTURES

The Role of Mining Intensity and Pre-existing Fracture Attributes on Spatial, Temporal and Magnitude Characteristics of Microseismicity in Longwall Coal Mining

Update and Test of a Seismicity Simulation Program Based on the Coulomb-Navier Failure Criterion and the Stress Transfer Mechanism

Statistical properties of seismic foreshocks and aftershocks associated with longwall mining: Implications from the Epidemic Type Aftershock Sequence model

Identification of geological faults by geophysical methods for risk assessment in underground mining

The critical earthquake concept applied to mine rockbursts with time-to-failure analysis

Numerical and Field Investigations of Dynamic Failure Caused by Mining-Induced Tremor Based on Focal Mechanism

Source parameters inversion of the global large earthquakes using 3D SEM Green's functions: Strain Green's function calculation and validation

A Stochastic Method for Simulating Near‐field Seismograms: Application to the 2016 Tottori Earthquake

Quantitative Energy-Based Evaluation of the Intensity of Mining-Induced Seismic Activity in a Fractured Rock Mass

Numerical investigation of progressive damage and associated seismicity on a laboratory fault

Pre-earthquake State Identification by Micro-earthquake Spike Trains Dissimilarity Analysis

Seismicity Modeling in Tasks of Seismic Hazard Assessment

Finite Element Method Simulation Of The Earthquake Preparation, Occurrence, And Recurrence Cycles

An Inversion-Based Microseismic Simulator for Fracture Diagnostics