Source parameters inversion of the global large earthquakes using 3D SEM Green's functions: Strain Green's function calculation and validation

Lei Zhang,Jinlai Hao,Wenze Deng,Chen Ji,Chuhan Zhang

DOI: https://doi.org/10.1093/gji/ggac135

IF: 3.352

2022-04-07

Geophysical Journal International

Abstract:Abstract Precisely constraining the source parameters of large earthquakes is one of the primary objectives of seismology. However, the quality of the results relies on the quality of synthetic earth response. Although earth structure is laterally heterogeneous, particularly at shallow depth, most earthquake source studies at the global scale rely on the Green's functions calculated with radially symmetric (1D) earth structure. To avoid the impact of inaccurate Green's functions, these conventional source studies use a limited set of seismic phases, such as long period seismic waves, broadband P and S waves in teleseismic distances (30 degrees < ∆ < 90 degrees), and strong ground motion records at close-fault stations. The enriched information embedded in the broadband seismograms recorded by global and regional networks is largely ignored, limiting the spatiotemporal resolution. Here we calculate 3D strain Green's functions at 30 GSN stations for source regions of 10 selected global earthquakes, with frequency up to 67 mill hertz (15 s), using SPECFEM3D_GLOBE and the reciprocity theorem. The 3D SEM mesh model is composed of mantle model S40RTS, crustal model CRUST2.0, and surface topography ETOPO2. We surround each target event with grids in horizontal spacing of 5 km and vertical spacing of 2.0∼3.0 km, allowing us to investigate not only the mainshock but also the background seismicity. In total, the response at over 210,000 source points is calculated in simulation. The number of earthquakes, including different focal mechanisms, centroid depth range, and tectonic background, could further increase without additional computational cost if they were properly selected to avoid overloading individual CPUs. The storage requirement can be reduced by two orders of magnitude if the output strain Green's functions are stored for periods over 15 s. We quantitatively evaluate the quality of these 3D synthetic seismograms, which are frequency and phase dependent, for each source region using nearby aftershocks, before using them to constrain the focal mechanisms and slip distribution. Case studies show that using a 3D earth model significantly improves the waveform similarity, agreement in amplitude and arrival time of seismic phases with the observations. The limitations of current 3D models are still notable, dependent on seismic phases and frequency range. The 3D synthetic seismograms cannot well match the high frequency (>40mHz) S wave and (>20mHz) Rayleigh wave yet. Though the mean time-shifts are close to zero, the standard deviations are notable. Careful calibration using the records of nearby better located earthquakes is still recommended to take full advantage of better waveform similarity due to the use of 3D models. Our results indicate that it is now feasible to systematically study global large earthquakes using full 3D earth response in a global scale.

geochemistry & geophysics

What problem does this paper attempt to address?

The problem that this paper attempts to solve is: how to more accurately constrain the source parameters of large global earthquakes by using three - dimensional (3 - D) seismic response functions. Specifically, the paper points out that although the Earth's structure has lateral heterogeneity in the shallow layer, most current global - scale earthquake source studies still rely on Green's functions calculated based on a radially symmetric (1 - D) Earth structure. This has led to limited quality of synthetic seismograms, which in turn affects the accuracy of source parameters. To overcome this problem, the authors propose a method to calculate the three - dimensional strain Green's functions for multiple global earthquakes using the three - dimensional Spectral Element Method (SEM) and the reciprocity theorem, and verify the effectiveness of these functions. This method can fully utilize the rich information in broadband seismograms recorded by global and regional networks, improving the spatial and temporal resolution of earthquake source parameters.

The main objectives of the paper include:
1. Calculate the three - dimensional strain Green's functions for selected global earthquake regions, with a frequency up to 67 mHz (15 seconds).
2. Verify the quality of these three - dimensional Green's functions, especially their waveform similarity, amplitude consistency, and arrival - time consistency with actual observed data.
3. Apply these three - dimensional Green's functions for point - source inversion to improve the estimation of source parameters for large earthquakes.

Through these steps, the authors hope to show that Green's functions calculated using a three - dimensional Earth model can significantly improve the fitting of earthquake waveforms, thereby more accurately determining the rupture process and source parameters of earthquakes.