Abstract:The paper reports the main features of electrochemical deposition of nickel-iron alloy from electrolyte based on the eutectic mixture of choline chloride and ethylene glycol, which is a typical representative of a new type of ionic liquids, deep eutectic solvents (DES). It is found that the iron content in the deposited alloy increases with both increasing the applied cathode current density and increasing the concentration of iron ions in the electrolyte and the introduction of water additives. Thus, variation in the current density and the concentration of water additive in electrolytes based on DES is the factor of influence on the kinetics of partial electrode reactions, and hence on the composition and properties of the coating. It is shown that it is possible to deposit uniform coatings with iron content up to 10–13% from the investigated electrolyte containing water additive (up to 10 wt.%) at the deposition current density not exceeding 1–1.2 A/dm2. The current efficiency of the alloy deposition is close to the theoretical value (97–99%), i.e. the electrodeposition is practically not complicated by electrochemical processes involving components of a deep eutectic solvent. The surface of pure nickel deposited from an electrolyte based on DES without additional water is quite uniform with a small number of defects, pitting and small pores, while coatings deposited from the electrolyte containing water additives are characterized by granular surface morphology with many asymmetric spheroidal crystallites. The electrodeposition of a nickel-iron alloy yields the surface built of irregular spheroids that overlap and form a scaly-like type of surface morphology. Nickel-iron electrolytic coatings containing up to ~7% Fe, formed from the ethaline-based electrolyte, are nanocrystalline solutions of iron in nickel with a face-centered cubic nickel lattice and an average nanocrystallite size of about 6–15 nm. Nickel-iron alloy coatings electrochemically deposited under the conditions established in this work may be considered as promising electrode materials for the creation of new cheap and highly efficient electrocatalysts for water electrolysis in hydrogen energy.

A review of the electroforming of iron and iron-nickel alloy

Electroplating of iron and its alloys

Electrolytic coating of iron-chromium alloy of sulphate-chloride electrolyte in machine parts recovery process modelling

Mechanical Properties and Microstructure of Rolled and Electrodeposited Thin Copper Foil

Effects of Technology Parameters on Alloy Foil with DC-electrodeposited Nanocrystalline Ni-Fe

Evaluating and monitoring nucleation and growth in copper foil

Effect of Alloying Elements and Processing Parameters on Microstructure and Properties of 1XXX Aluminium Alloys

Removal of Iron From Aluminum: A Review

The Effects of Additives on the Physical Properties of Electroformed Nickel and on the Stretch of Photoelectroformed Nickel Components

Environmental Testing of Iron-Based Amorphous Alloys

Bending deformation and indentation hardness of electrochemically deposited nanocrystalline nickel-iron alloys

Review—Preparation of Hafnium Metal by Electrolysis

CoCrFeMnNi High-Entropy Alloy Thin Films Electrodeposited on Aluminum Support

A Review on Current Status of Zinc-Iron-phoshporus Electroplating

Nanostructure Analysis of Anodic Films Formed on Aluminum-Focusing on the Effects of Electric Field Strength and Electrolyte Anions

Fabrication and characterization of anodic films onto the FeCrAl stainless steel in ethylene glycol electrolyte

ELECTRODEPOSITION OF NANOCRYSTALLINE NICKEL-IRON ALLOY FROM AN ELECTROLYTE BASED ON A NEW TYPE OF IONIC LIQUIDS – DEEP EUTECTIC SOLVENT

Electroforming as a Novel One-Step Manufacturing Method of Structured Aluminum Foil Current Collectors for Lithium-Ion Batteries

REVIEW ON EXFOLIATION SUSCEPTIBILITY OF ALUMINIUM ALLOYS AND QUANTITATIVE MEASUREMENT METHOD

Elucidating the Influence of Electrolyte Additives on Iron Electroplating Performance