Abstract:For low costs, numerical simulation is an effective method to reveal the internal mechanisms inside a thermal plasma torch. Various simulation models for studying the inside or outside characteristics of thermal plasma torches have been built and discussed. However, to reveal the inside mechanisms of thermal plasma torches under various working conditions to support the materials processing, more attention should be paid to building precise models of laminar plasma torches. Thus, based on the user-defined function (UDF) and user-defined scalar (UDS) of ANSYS Fluent software, the assumptions, governing equations, boundary conditions, and solving method were discussed in detail, and a corresponding numerical model of a homemade laminar plasma torch was first built. For verifying the effectiveness of the proposed numerical model and studying the influence of the gas components on the arc characteristics, the working conditions and experimental setups were introduced in sequence. Finally, the numerical and experimental results of the homemade laminar plasma torch were obtained and discussed in detail. The study results show that: 1 The axial temperature of the plasma torch could be divided into three sections along the axis: peak temperature area (10 mm < x < 20 mm), stable temperature area (20 mm < x < 62 mm) and decrease temperature area (62 mm < x < 95 mm). Under the same input conditions, when pure argon gas was used, the peak temperature at the outlet was reached at approximately 7590 K, while for pure nitrogen and 50%Ar + 50%N2, the corresponding peak temperatures were 6785 K and 7402.2 K, respectively. 2 The axial velocity of pure nitrogen is much higher than that of pure argon and 50%Ar + 50%N2, while that of pure argon and 50%Ar + 50%N2 has little difference. In addition, when nitrogen gas was used, the peak velocity at the outlet reached 185 m/s, whereas, for argon gas and 50%Ar + 50%N2, the corresponding peak velocities were 146 m/s and 169 m/s, respectively. 3 The simulated arc voltage trends under different working conditions are well in accordance with the experimental arc voltage trends.

First Step in Theoretical Approach in Study of Mars and Titan Atmospheres with an Inductively Coupled Plasma Torch

Overview on Studies of Martian Like Co2-N2 Mixture by Inductively Coupled Plasma Torch

Definition of a New Level One Test Case Measurements of Equilibrium Radiation from an Inductively Coupled Plasma in the Near-UV to Near-IR Spectral Region for a Titan-Type N2-CH4 Mixture. Preliminary Results

An EUV Non-Linear Optics Based Approach to Study the Photochemical Processes of Titanś Atmosphere

Arc Plasma Torch Modeling

Theoretical Aspects and Design of a Low-Power, Low-Flow-Rate Torch in Inductively Coupled Plasma Atomic Emission Spectroscopy

Main Issues for a Fully Predictive Plasma Spray Torch Model and Numerical Considerations

Gas Temperature Measurements and Imaging Analysis in Atmospheric-Pressure Microwave Air Induced Plasma Torch

Effect of Cathode-Plasma Coupling on Plasma Torch Operation Predicted by a 3D Two-Temperature Electric Arc Model

Modeling of the Arc Characteristics inside a Thermal Laminar Plasma Torch with Different Gas Components

In situ investigation of neutrals involved in the formation of Titan tholins

Influence of secondary gas on control characteristics of ICP-RF plasma torches

Multi-domain analysis and prediction of the light emitted by an inductively coupled plasma jet

Hypervelocity Impact Effect of Molecules from Enceladus’ Plume and Titan’s Upper Atmosphere on NASA’s Cassini Spectrometer from Reactive Dynamics Simulation

Design and Construction of a Low-Flow, Low-Power Torch for Inductively Coupled Plasma Spectrometry

Modelling and Experimental Validation of the Flame Temperature Profile in Atmospheric Plasma Coating Processes on the Substrate

In situ multi-band apparent emissivity measurements of aerospace materials in inductively coupled plasma flows

Measurements and semi-empirical calculations of CO2+CH4 and CO2+H2 collision-induced absorption across a wide range of wavelengths and temperatures. Application for the prediction of early Mars surface temperature

Validation of the thermo-chemical approach to modelling of the CO$_2$ conversion in atmospheric pressure microwave gas discharges

Abel transform of exponential functions for planetary and cometary atmospheres with application to observation of 46P/Wirtanen and to the OI 557.7 nm emission at Mars.

Experimental study of an oxygen plasma cutting torch: II. Arc–material interaction, energy transfer and anode attachment