Abstract:Shanghai Soft X-ray FEL Test Facility (SXFEL) has started the infrastructure construction in 2015. All beam diagnostic systems are under processing and measurement, including C-band Low-Q cavity BPMs. This paper presents the progress of the cavity BPM system, including design and the measurements on a lab platform. Measurements shown that the cavity BPM frequency is 4.7GHz ± 8MHz, and the complete test platform verify that the cavity BPM system, which including signal processing electronics can work as expected. INTRODUCTION The SXFEL project at the Shanghai Synchrotron Radiation Facility (SSRF) campus serves as a test facility of China’s future hard X-ray FEL user facility, while it can be easily upgraded to a FEL user facility at“waterwindow” spectral region for scientific investigations with high brilliance X-ray pulses of ultra-fast and ultra-high resolution processes in material science and physical biosciences. The construction of the SXFEL has started since April 2015, and the first X-ray FEL light is planned to be delivered to the beam line in 2017. The SXFEL consists of following parts: 1. A photo-injector generating a bright electron beam and accelerating it to ~ 130 MeV. 2. The main linear accelerator, where the electron beam is longitudinally compressed and accelerated to ~ 840 MeV. 3. The FEL undulator complex where X-ray radiation is generated. 4. The photon beam transport & diagnostic line. To achieve the physical design of SXFEL, the diagnostic system need to achieve requirements listed in Table 1, and the dynamic is 0.1nC~0.5nC. CAVITY BPM SYSTEM The cavity BPMs have been chosen for the real time measurements of the electron beams positions along the undulator of the SXFEL. The layout is shown in Fig. 1. Figure 1: Layout of cavity BPM along undulator. Table 1: Beam Diagnostics System Specification Parameter Main technical specifications Position Stripline BPM, Resolution: 10μm@0.5nC Cavity BPM, Resolution: 1μm@0.5nC Size YAG/OTR, Resolution:30μm@1nC, Repeatablity:50μm Charge ICT, Resolution:1% Length CSR, Resolution:100fs Arrive time Phase cavity, Resolution:200 fs Cavity BPM Pickups The cavity BPM system consists of the cavity BPM probes, the RF front-end and data acquisition (DAQ) electronics is shown in Table 2. The working frequency of the position mode and the reference cavity of the CBPM are designed to be 4.7GHz preliminary to avoid the interference of the dark current caused by the frequency multiplication of the RF. The signals will be lead out through the 50Ω load and the system quality factor will be mainly determined by the external quality factor. Table 2: The Cavity BPM Design Parameter Parameter TM110 TM010 Frequency 4.7GHz 4.7GHz Q ~60 ~60 Ports number 4 2 Signal amplitude@50Ω 12mV/μm/nC (peak) 100V/nC (peak) CBPM responses with a series of simulated electron beams passing the CBPM at different positions have been modeled with MAFIA. The output signal and the corresponding spectrum at the electrode of the CBPM are shown here in Fig. 2. Stage-1 Stage-2 UN-POP UN-POP UN-POP UN-POP UN-POP UN-POP UNPRF

Status of the ILC Main Linac BPM R&D

Cavity BPM System Tests for the ILC Spectrometer

Progress of Cavity Beam Position Monitor at SXFEL

LOW Q CAVITY BPM STUDY FOR THE BEAM POSITION MEASUREMENT OF NANOSECOND SPACED ELECTRON BUNCHES *

In situ beam trajectory tilt measurement based on single cavity beam position monitor

Study of the Crosstalk Evaluation for Cavity BPM

Optimization of the Cavity Beam-Position Monitor System for the Shanghai Soft X-ray Free-Electron Laser User Facility

On-line crosstalkmeasurement and compensation algorithm study of sxfel digital bpm system ∗

Beam Position Monitor Electronics Upgrade for Fermilab Switchyard

High Resolution Cavity BPM for ILC Final Focal System (IP-BPM)

The Development of Low-Q Cavity Type Beam Position Monitor with a Position Resolution of Nanometer for Future Colliders

Initial PIP-II Beam Current Monitor Fault Case Analyses & Beam Position Monitor Linearity Studies in CST Studio Suite

Design and Offline Testing of a Resonant Stripline Beam Position Monitor for the IRFEL Project at NSRL

A New Digital Beam Position and Phase Measurement Implementation Based on a Field Programmable Gate Array for the High Intensity Heavy-Ion Accelerator Ilinac

Button-Type Beam Position Monitor Development for Fourth-Generation Synchrotron Light Sources: Numerical Modeling and Test Bench Measurements

DESIGN AND COLD TEST OF RE-ENTRANT CAVITY BPM FOR HLS*

Design and Cold Test of S-BAND Cavity BPM for HLS

Latest R\&D news and beam test performance of the highly granular SiW-ECAL technological prototype for the ILC

Overview of the SiLC R&D Activities

Status of Higher Order Mode Beam Position Monitors in 3.9 GHz Superconducting Accelerating Cavities at FLASH

Design and Simulation of Beam Position Monitor for 200 MeV Linac in HLS