Abstract:Most Individual Blade Control (IBC) approaches have attempted to suppress rotor vibration by actively altering the varying aerodynamic loads on the blade using techniques such as trailing edge servo-flaps or imbedded piezoelectric fibers to twist the blade. Unfortunately, successful implementation of these approaches has been hindered by electromechanical limitations of piezoelectric actuators. The Smart Spring is an unique IBC approach that is designed to suppress the rotor vibration by adaptively altering the “structural impedance” at the blade root out of phase from the time varying aerodynamic forces. It overcomes many limitations associated with the capabilities of piezoelectric actuators inherent in other IBC approaches. The details of the Smart Spring concept as a class of actively Tunable Vibration Absorbers (TVA) for the rotor blade application is presented in this paper. A proof-of-concept hardware model of the Smart Spring was fabricated and a real-time adaptive control algorithm was implemented to demonstrate the concept as an actively TVA. The initial dynamic tests using a mechanical shaker achieved significant vibration suppression at harmonic peaks as well as the broadband reduction in vibration. Further testing of the hardware was conducted in a wind tunnel using a non-rotating blade to evaluate the performance of the device in a more representative rotor blade aerodynamic environment. Shaker test and wind tunnel test results verified the capability of the Smart Spring to suppress multiple harmonic components in rotor vibration through adaptive control of the structural impedance at the blade root. * Research Associate, member AIAA. † Group Leader, senior member AIAA. ‡ Post Doctoral Fellow. § Professor, member AIAA. INTRODUCTION Significant structural vibration due to unsteady aerodynamics caused by Blade Vortex Interaction (BVI) is a notable and undesirable characteristic of helicopter flight. Vibratory hub loads are transferred throughout the helicopter structure contributing to poor ride quality for passengers and fatigue of expensive structural components. In addition to passive techniques, such as vibration absorbers or addition of mass to tune blades, active control solutions are currently being investigated to suppress rotor vibration. Active approaches promise vibration suppression in a broadband of frequencies unlike passive techniques that are typically capable of suppressing vibration over a narrow frequency range. The Individual Blade Control (IBC) approach is one of the most promising active vibration suppression methods currently under development. IBC places actuators and sensors on the blade to control each blade independently and simultaneously to suppress the vibration at the source. IBC using active material actuators for rotor vibration suppression has been implemented using two distinct actuation concepts, namely, discrete and integral. The discrete actuation concept employs actuators imbedded in the blade to control a trailing edge servo-flap. Unfortunately, a fundamental problem with this approach is the limited displacement capability of piezoelectric actuators. Robust and compact displacement amplification devices are necessary to obtain the required flap deflection under the extreme aerodynamic environment of a rotor. In the integral actuation concept, the actuator system is either embedded or bonded to the blade skin along the span to obtain a smooth continuous structural deformation. The drawback with this approach is the requirement of very high voltages to induce sufficient structural deformation from the actuators to generate the required blade twist for rotor vibration suppression.

Individual Blade Control Approach for Active Vibration Suppression of a Lift-Offset Coaxial Rotorcraft

Simultaneous Vibration Reduction and Performance Improvement of Helicopter Rotor Using Individual Blade Pitch Control with Multiple Harmonic Inputs

Individual Blade Control for Component Load Alleviation Using Higher-Order Linear Time-Invariant Models

Reducing aerodynamic vibration of rigid rotors with retreating side active control avoidance

Smart Spring - an Actively Tunable Vibration Absorber Designed to Control Aeroelastic Response

Feasibility and Effectiveness of a Higher Harmonic Control System for a Medium Utility Helicopter

Active Vibration Damping Using Rotor Torque Control in Electric Aircraft

Vibration Suppression of Base-Excited Rotors Supported by Active Magnetic Bearings Based on an Augmented Kalman Compensator

Active Vibration Control of a Flexible Rotor in Magnetically Suspended High-Speed Motor to Pass the First Bending Critical Speed with Optimal Phase Compensation Control

Feedforward Decoupling Control for Rigid Rotor System of Active Magnetically Suspended High‐speed Motors

Vibration Control for Active Magnetic Bearing High-Speed Flywheel Rotor System with Modal Separation and Velocity Estimation Strategy

Multiobjective Vibration Control for the Noncollocated Active Magnetic Bearings Flexible Rotor Systems

Multi-Objective Optimal Design of Μ–controller for Active Magnetic Bearing in High-Speed Motor

Active Vibration Control of a Non-collocated AMBs Flexible Rotor System to Pass the First Bending Critical Speed

Active vibration reductions for airframe and human body of UH-60A helicopter in low- and high-speed flights

Unbalance Compensation for Active Magnetic Bearing Rotor System Using a Variable Step Size Real-Time Iterative Seeking Algorithm.

An optimal vibration control strategy of AMB-flexible rotor syxstem

Output Feedback Dynamical Compensation Via EigenStructure Assignment for Active Magnetic Bearings-Rigid Rotor Systems.

A Novel Parallel Multi-Harmonic Global Multi-Channel Control Algorithm for Helicopter Active Vibration Control

A novel constrained optimal tuning method with application to helicopter rotor track and balance

Experimental investigations on active control of multifrequency helicopter vibrations using discrete model predictive sliding mode control