Abstract:This paper reports the results of scratch tests on three rocks (Bonne Terre Dolomite, Alabama Marble and Dunnville Sandstone) conducted at depths of cut ranging from 0.2 mm to 2.6 mm. The experiments were performed on slabs of thickness slightly smaller than the cutter width, with a camera recording the entire cutting process. The test results reveal the existence of three cutting regimes: ductile, fragmentation, and brittle with increasing depth of cut. The regimes differ by the failure mode, the dependence of the specific energy ε on the depth of cut d, and the fragment shapes. In the ductile regime, ε∼d0 and the fragments are constitutive grains of the rock or powder as a result of intense shearing. In the fragmentation regime, ε∼d−1/2 and the fragments is a mix of ductile-type particles and flake-like chips also the product of shear failure. Finally, the brittle regime is characterized by ε∼d−1 and is essentially associated with chip-like fragments that come in two varieties depending on whether they are created by shear or by tension. The d−1-dependence of the specific energy can only be observed if the rock is sufficiently homogeneous at the scale of the experiment. The distinction between different modes of failure is based on evidence from video recording and fractography with a Scanning Electron Microscope. It is shown that the dominance of tensile over shear fracture is intimately related to the existence of a crushed zone, which acts as a wedge to initiate a tensile macrocrack in a compressive stress field. Finally, an analysis of the energy partitioning in the brittle regime indicates that the energy dissipated in creating new surfaces with a tensile crack is actually negligible compared to the energy expended in the formation of the wedge. This result indicates that the mode I toughness cannot be determined from the specific energy in the brittle regime, on the basis of a model of a crack parallel to the free surface, in contradiction with published claims to that effect. Finally, this experimental investigation clarifies some confusion in the literature, rooted on assuming the existence of only two modes of failure, ductile and brittle.

Use of a nanoindentation fatigue test to characterize the ductile-brittle transition

Approach to investigate pre-nucleation fatigue damage of cyclically loaded metals using Vickers microhardness tests

A Nanoindentation Study of the Deformation Mode for Nanostructured Ductile/brittle Multilayers: Cracking Versus Shear Banding

Experimental Research on Micro Scale Mechanics Behavior of Potassium Dihydrogen Phosphate Crystal

Nanoindentation stress-strain for Fracture Analysis and computational modeling for hardness and modulus

An experimental investigation of brittle failure mechanisms in scratch tests of rock

A new method for microscale cyclic crack growth characterization from notched microcantilevers and application to single crystalline tungsten and a metallic glass

Small-Scale Mechanical Testing of Cemented Carbides from the Micro- to the Nano-Level: A Review

Quantification of degradation of nanomechanical properties around a static damage

Nanoindentation Induced Anisotropy of Deformation and Damage Behaviors of MgF2 Crystals

Depth-sensing ductile and brittle deformation in 3C-SiC under Berkovich nanoindentation

Size effects in fatigue crack growth in confined volumes: A microbending case study on nc Ni

Anisotropic Fatigue Behavior of Human Enamel Characterized by Multi-Cycling Nanoindentation

Description of the Nanoindentation Unloading Curves with a Universal Function: Theoretical Consideration and Applications to Brittle Materials

Indentation-based Methods to Assess Fracture Toughness for Thin Coatings

Indentation of Coatings at micro/nano scale: Crack formation and deflection

Effect of normal load and roughness on the nanoscale friction coefficient in the elastic and plastic contact regime

Novel nanoindentation strain rate sweep method for continuously investigating the strain rate sensitivity of materials at the nanoscale

Calibration and data analysis routines for nanoindentation with spherical tips

Computational Monitoring of an Initial Fatigue Crack Incubation and Growth in a Smooth Specimen

Experimental investigation and micromechanical modeling of the brittle-ductile transition behaviors in low-porosity sandstone