Abstract:Carbon nanotube/continuous carbon fiber reinforced poly(ethylene terephthalate) (CNT/CCF/PET) composites are prepared by melt impregnating. The effects of CF and CNT content on the mechanical properties, melt and crystallization behaviors, and submicroscopic morphology of CNT/CCF/PET composites are studied. The tensile test results show that the increase of CF and the addition of appropriate amount of CNT improved the tensile strength and tensile modulus of the composites. When the content of CNT is 1.0 wt% and the content of CF is 56 wt%, the properties of the composites are the best, with tensile strength of 1728.7 MPa and tensile modulus of 25.1 GPa, which is much higher than that of traditional resin matrix composites. The results of dynamic mechanical analysis (DMA) show that the storage modulus of the composites increased with the increase of CF and CNT content. In particular, the addition of CNT greatly reduced the loss modulus of the composites. Morphological analysis show that the addition of CNT improved the fiber–matrix interface of the composite, which changes from fiber pull-out and fracture failure to fiber matrix fracture failure, and the fiber matrix interface is firmly bonded. In addition, there are polymer coated CNT protrusions on the surface of the fiber was observed. The results of differential scanning calorimetry (DSC) show that the melting temperature and crystallization temperature of the composites increased with the increase of CF content. The addition of CNT had little effect on the melting temperature of the composites, but it further improved the crystallization temperature of the composites. The effect of CNT content on the crystallization kinetics of the composites is studied. The non-isothermal crystallization kinetics of the composites is described by Jeziorny's improved Avrami equation. The results show that CNT has a great influence on the crystallization type of the composites. As a nucleating agent, CNT has obvious heterogeneous nucleation effect in the composites, which improves the crystallization rate of PET.

Effect of thiol-modified carbon nanotubes on curing, mechanical, and thermophysical properties of poly(ethylene trisulfide)

The Curing Behavior and Properties of Diglycidyl Ether of 4,4′-Bis(4-hydroxybenzoyloxy)-3,3′,5,5′-tetramethylbiphenyl and Its Composites with Multi-Wall Carbon Nanotubes

Properties of Carbon Nano-Tubes–cf/sic Composite by Precursor Infiltration and Pyrolysis Process

Liquid Crystalline Pet/60hba-Mwnts Composite: Synthesis, Characterization, and Properties

Mechanical Properties, Melting and Crystallization Behaviors, and Morphology of Carbon Nanotubes/Continuous Carbon Fiber Reinforced Polyethylene Terephthalate Composites

Effect of Carbon Nanotube on Thermal, Tribological and Mechanical Properties of 3D Printing Polyphenylene Sulfide

Impact of In-Situ Functionalization of Carbon Nanotubes Using Bis(Triethoxysilylpropyl) Tetrasulfide on the Properties of EPDM/SBR–CNT Composites

Effect of Carbon Nanotubes on the Mechanical Properties and Crystallization Behavior of Poly(ether Ether Ketone)

Effect of carbon nanotubes on thermoset curing and mechanical properties of carbon fiber reinforced epoxy resin laminates fabricated by self‐resistance electric heating

Effect of carbon nanotubes on mechanical performance and thermal stability of recyclable thermosets poly(hexahydrotriazine)s-based composites

Effects of carboxylated carbon nanotubes on the phase separation behaviour and fracture-mechanical properties of an epoxy/polysulfone blend

Electrical and flame-retardant properties of carbon nanotube/poly(ethylene terephthalate) composites containing bisphenol A bis(diphenyl phosphate)

Effect of Nitrile-Functionalization and Thermal Cross-Linking on the Dielectric and Mechanical Properties of PEN/CNTs–CN Composites

Microstructure of Carbon Nanotubes/pet Conductive Composites Fibers and Their Properties

Microstructure and Properties of Poly(butylene Terephthalate)/poly(ethylene Terephthalate) Composites Based on Carbon Nanotubes/graphene Nanoplatelets Hybrid Filler Systems

Effect of functionalization of multiwalled carbon nanotubes with aminated poly(ether sulfone) on thermal and mechanical properties of poly(ether ether ketone) nanocomposites

Effect of Carbon Nanotubes on the Crystallization and Properties of Semi-Crystalline Polyarylene Ether Nitrile

The effects of carbon nanotubes selective location on the structures and properties of polyphenylene sulfide/polyamide 66 fibers

Preparation and Property of Carbon-Nanotubes/pet

Effect of bis(3-triethoxysilylpropyl) tetrasulfide on the crosslink structure, interfacial adhesion, and mechanical properties of natural rubber/cotton fiber composites

Viscoelasticity and thermal stability of poly(arylene ether nitrile) nanocomposites with various functionalized carbon nanotubes