Abstract:Purpose The purpose of this study, most recent advancements in threedimensional (3D) printing have focused on the fabrication of components. It is typical to use different print settings, such as raster angle, infill and orientation to improve the 3D component qualities while fabricating the sample using a 3D printer. However, the influence of these factors on the characteristics of the 3D parts has not been well explored. Owing to the effect of the different print parameters in fused deposition modeling (FDM) technology, it is necessary to evaluate the strength of the parts manufactured using 3D printing technology. Design/methodology/approach In this study, the effect of three print parameters − raster angle, build orientation and infill − on the tensile characteristics of 3D-printed components made of three distinct materials − acrylonitrile styrene acrylate (ASA), polycarbonate ABS (PC-ABS) and ULTEM-9085 − was investigated. A variety of test items were created using a commercially accessible 3D printer in various configurations, including raster angle (0°, 45°), (0°, 90°), (45°, −45°), (45°, 90°), infill density (solid, sparse, sparse double dense) and orientation (flat, on-edge). Findings The outcome shows that variations in tensile strength and force are brought on by the effects of various printing conditions. In all possible combinations of the print settings, ULTEM 9085 material has a higher tensile strength than ASA and PC-ABS materials. ULTEM 9085 material's on-edge orientation, sparse infill, and raster angle of (0°, −45°) resulted in the greatest overall tensile strength of 73.72 MPa. The highest load-bearing strength of ULTEM material was attained with the same procedure, measuring at 2,932 N. The tensile strength of the materials is higher in the on-edge orientation than in the flat orientation. The tensile strength of all three materials is highest for solid infill with a flat orientation and a raster angle of (45°, −45°). All three materials show higher tensile strength with a raster angle of (45°, −45°) compared to other angles. The sparse double-dense material promotes stronger tensile properties than sparse infill. Thus, the strength of additive components is influenced by the combination of selected print parameters. As a result, these factors interact with one another to produce a high-quality product. Originality/value The outcomes of this study can serve as a reference point for researchers, manufacturers and users of 3D-printed polymer material (PC-ABS, ASA, ULTEM 9085) components seeking to optimize FDM printing parameters for tensile strength and/or identify materials suitable for intended tensile characteristics.

Experimental Investigation of Parameters Affecting the Tensile Strength of Silicone-Filled 3D Printed ABS Products

Correlation between production parameters and mechanical properties of ABS plus p430 fused deposition material

Effects of fused filament fabrication (FFF) process parameters on tensile and flexural properties of ABS/PLA multi-material

Using extrusion-based 3D printing technology to investigate the impact of changing print conditions on tensile characteristics

Experimental Study of the Tensile Behavior of Structures Obtained by FDM 3D Printing Process

Infill pattern and density effects on the tensile properties of 3D printed PLA material

The effects of infill density and pattern on the strength of marine small craft building by additive manufacturing method

Synthesis and Investigation of Mechanical Properties of the Acrylonitrile Butadiene Styrene Fiber Composites Using Fused Deposition Modeling

An Investigation of 3D Printing Parameters on Tensile Strength of PLA Using Response Surface Method

Mechanical Properties and Performance of 3D-Printed Acrylonitrile Butadiene Styrene Reinforced with Carbon, Glass and Basalt Short Fibers

Mechanical Properties of Raw Filaments and Printed Specimens: Effects of Fiber Reinforcements and Process Parameters

Investigating the influence of 3D printing parameters on the mechanical characteristics of FDM fabricated (PLA/Cu) composite material

Effect of print parameters on the tensile strength and built time of FDM-printed PLA parts

Effect of Infill Density and Printing Patterns on Compressive Strength of ABS, PLA, PLA-CF Materials for FDM 3D Printing

Assessment of the mechanical properties of PC/ABS blends for functional prototyping by FFF 3D printing

Mechanical properties evaluation of FFF-printed ABS samples based on different process parameters combined with ANOVA and regression analysis

Analysis of mesostructural characteristics and their influence on tensile strength of ABS specimens manufactured through fused deposition modeling

Analysis of the Impact of Cooling Lubricants on the Tensile Properties of FDM 3D Printed PLA and PLA+CF Materials

Impact of infill density on morphology and mechanical properties of 3D printed ABS/CF-ABS composites using design of experiments

Effect of Infill Line Direction on Tensile and Flexural Properties of Poly(Lactic Acid) Samples during 3D Printing

The Influence of Manufacturing Parameters on the Mechanical Behaviour of PLA and ABS Pieces Manufactured by FDM: A Comparative Analysis