Abstract:Polypropylene-based multiphase compositions with a disperse elastomer phase provide superior impact strength. Making this property indifferent to processing steps requires stabilization of the morphology of these materials. Various approaches have been tested over time, each of which shows limitations in terms of performance or applicability. Using polyethylene (PE) homo- and copolymers capable of silane-based crosslinking as modifiers was explored in the present study, which allows decoupling of the mixing and crosslinking processes. Commercial silane-copolymerized low-density PE (LD-PEX) from a high-pressure process and silane-grafted high-density PE (HD-PEX) were studied as impact modifiers for different types of PP copolymers, including non-modified reference PE grades, LDPE and HDPE. Blends based on ethylene-propylene random copolymers (PPR) and based on impact- (PPI) and random-impact (PPRI) copolymers show improvements of the stiffness-impact balance; however, to different degrees. While the absolute softest and most ductile compositions are achieved with the already soft PPRI copolymer base, the strongest relative effects are found for the PPR based blends. Modifiers with lower density are clearly superior in the toughening effect, with the LD-PEX including acrylate as second comonomer sticking out due to its glass transition around -40 °C. The impact strength improvement found in most compositions (except at very high content) results, however, not from the expected phase stabilization. For comparable systems, particle sizes are normally higher with crosslinking, probably because the process already starts during mixing. Thermoplastic processability could be retained in all cases, but the drop in melt flow rate limits the practical applicability of such systems.

The influence of phase morphology of polycarbonate/polyethersulfone blends on the failure behavior between the blends and polyurethane in the peel test

Effect Of Polyethersulfone On The Mechanical And Rheological Properties Of Polyetherimide-Modified Epoxy Systems

Viscoelastic Effects on the Phase Separation in Thermoplastics-Modified Epoxy Resin

Visualization of Poly(ether Imide) and Polycarbonate Blending in an Internal Mixer

Study on the Polyethersulfone/bismaleimide Blends: Morphology and Rheology During Isothermal Curing

Relationship between structure and properties in high-performance PA6/SEBS-g-MA/(PPO/PS) blends: The role of PPO and PS

Tensile and Transformational Behavior of Poly(Ether Sulfone) Polycarbonate Blends

Phase Morphology and Impact Toughness of Impact Polypropylene Copolymer

Note: Interfacial layer and phase inversion behavior in the blend of polyethersulfone and polycarbonate

Fracture Toughness and Fracture Mechanisms of PBT/PC/IM Blends PART IV Impact Toughness and Failure Mechanisms of PBT/PC Blends Without Impact Modifier

Plastic damage mechanisms of polypropylene/polyamide 6/polyethelene-octene elastomer blends under cyclic tension

Phase behaviour, mechanical properties and thermal stability of thermosetting polymer blends of unsaturated polyester resin and poly(ethylene oxide)

Investigation of Toughening Mechanisms in Elastomeric Polycarbonate Blends through Morphological and Mechanical Characterization at Small and Medium Strain Rates

Fracture toughness and fracture mechanisms of PBT/PC/IM blends: Part V Effect of PBT-PC interfacial strength on the fracture and tensile properties of the PBT/PC blends

Polyolefin Blends with Selectively Crosslinked Disperse Phase Based on Silane-Modified Polyethylene

Investigation on Phase Separation Kinetics of Polyolefin Blends Through Combination of Viscoelasticity and Morphology.

Influence Factors of Internal Structure and Interfacial Compatibility of UHMWPE Fiber/sebs Resin Composites: Processing Parameters, Structure of Fiber and Nature of Resin

Phase morphology, crystallization behavior and mechanical properties of poly(L-lactide) toughened with biodegradable polyurethane: Effect of composition and hard segment ratio

Elucidating the impact of microstructure on mechanical properties of phase-segregated polyurea: Finite element modeling of molecular dynamics derived microstructures

Effect of crystalline form on the tribological properties of PA46/HDPE polyblends

Concurrently Enhanced Mechanical Properties and Capacitive Performance in All-Organic Dielectric Polymer Blend Via Phase Separation