Abstract:Polypropylene hollow fiber membrane (PPHFM) contactor, with aqueous solution absorbent such as sodium hydroxide (NaOH), monoethanolamine (MEA) and diethanolamine (DEA), was designed and used to separate and fix CO2 from CO2/N2 gas mixtures. The factors that influence the separation properties of CO2/N2 were investigated. It was found that the CO2 removal efficiency is the best by using MEA solution as absorbent. The overall mass transfer coefficient (K) increases with the increase of liquid flow, gas flow and the concentration of the absorbent; however, it decreases with the carbon dioxide concentration in the gas mixture and the temperature of the absorbent solution. Preliminary results showed that carbon dioxide can be fixed efficiently into sodium carbonate and/or sodium bicarbonate with NaOH as the absorbent in the membrane contactor. Pure carbon dioxide, on the other hand, can be produced when MEA or DEA was used as the absorbent. INTRODUCTION Membrane separation of gases has emerged into an important unit operations technique offering specific advantages over more conventional separation procedures (e.g. cryogenic distillation and adsorption). One can envisage that these technologies will also make great contribution to the growth of new research area, such as carbon dioxide capture from flue gas. However, even through there are a large number of potential applications for gas separation with polymer membranes, only relatively few of them have become applied in practice. The potential application of a polymer as a separation membrane depends upon the possible throughput and the purity of product. This means that both the permeability coefficient for the gas that is transported more rapidly and the selectivity should be as large as possible. However, it was found that simple structural modifications, which lead to increases in polymer permeability usually, cause losses in permselectivity and vice versa. This so-called ′′trade-off′′ relationship is well described in the literature. It is thus possible to find polymers that exhibit high selectivity and low permeability and vice versa, in addition to that combine low selectivity with low permeability. There do not appear to be any polymers that show the desired trend to large values for both permeability and selectivity. Therefore, new membrane materials and technologies should be exploited to accommodate new applications, such as the simultaneous separation and capture of carbon dioxide from flue gas. TECHNOLOGY Membrane contactors are devices that achieve gas/liquid or liquid/liquid mass transfer without dispersed one phase within another. As schematically represented in Figure 1, they are accomplished by passing the fluid on opposite side of a microporous membrane or a composite membrane (e.g. microporous membrane coated with PDMS rubber). The porous membrane acts as a non-selective barrier between both phases. Separation is determined by the reaction of one component in the gas mixture with the absorbent in the liquid. Figure 1. Schematic rep This approach offers a numb contactor for gas sorption, such m), no flooding and foaming p low energy consumption and eas composite membranes, the main turn, low energy consumption), with absorbent variation. A sim listed in Table 1. P

CO 2 capture in a novel rotating spiral contactor with hydraulic seal: Hydromechanics, mass transfer and modeling

Mass Transfer Process of Co2 Absorption Through Non-Porous Hollow Fibre Contactor

CO2 Capture in a Miniaturized Annular Rotating Device with Countercurrent Flow

Gas/Liquid Operations in the Taylor-Couette Disc Contactor: Continuous Chemisorption of CO2

Understanding the performance of membrane for direct air capture of CO2

Modeling of CO2 Mass Transport Across a Hollow Fiber Membrane Reactor Filled with Immobilized Enzyme

Thermodynamic Exploration of Two-Stage Vacuum-Pressure Swing Adsorption for Carbon Dioxide Capture

Chemisorption of CO 2 in a gas–liquid vortex reactor: An interphase mass transfer efficiency assessment

Integration of membrane contactors and catalytic solvent regeneration for efficient carbon dioxide capture

Effects of Varying Spiral-Ring Pitches on CO2 Absorption by Amine Solution in Concentric Circular Membrane Contactors

Exploiting an Alternative Co2 Absorption Process by Efficient Solvent Mixture

CO2 capture in a hollow fiber membrane contactor coupled with ionic liquid: Influence of membrane wetting and process parameters

Development of a membrane dispersion micro-absorber for CO 2 capture

Separation and Fixation of Carbon Dioxide Using Polymeric Membrane Contactor

Kinetics, Thermodynamics, and Mechanism of a Novel Biphasic Solvent for CO2 Capture from Flue Gas

Investigation of CO2 Absorption Rate in Gas/Liquid Membrane Contactors with Inserting 3D Printing Mini-Channel Turbulence Promoters

Two-Dimensional Conjugated Mass Transfer of Carbon Dioxide Absorption in a Hollow-Fiber Gas-Liquid Membrane Contactor

A Comprehensive Parametric Study on CO2 Removal from Natural Gas by Hollow Fiber Membrane Contactor: A Computational Fluid Dynamics Approach

Direct air capture with amino acid solvent: Operational optimization using a crossflow air‐liquid contactor

Multi-field synergy study of CO2 capture process by chemical absorption

Using Expansion Units to Improve CO2 Absorption for Natural Gas Purification - A Study on the Hydrodynamics and Mass Transfer