Abstract:Besides the design and synthesis of nonfullerene acceptors, the selection of polymer donors is also critical in determining the photovoltaic performance of nonfullerene organic solar cells (OSCs). However, the selection criteria of polymer donors for nonfullerene OSCs has been rarely investigated. In this work, a novel nonfullerene acceptor (MDB) with spa-hybridized-carbon-free ladder-type skeleton was developed and used as a model compound to study the effects of miscibility and molecular ordering in determining the performance of MDB-based solar cells. In order to achieve matched energy levels and complementary absorption, three wide-bandgap polymers (PM6, T71, and P3HT) with different chemical structures were selected to blend with MDB for OSCs. The donor:acceptor miscibilities of the three blends were estimated by contact angle measurements, while their crystallinity and phase separation were investigated by grazing incidence wide-angle X-ray scattering characterization and atomic force microscopy measurement, respectively. The interfacial tension values between MDI3 and PM6, MDB and J71, as well as MDB and P3HT were determined as 0.49, 0.16, and 2.00 mN.m(-1), in that order. Owing to the proper miscibility between MDB and PM6, the resulting blend film exhibits suitable phase separation, "face-on" molecular orientation as well as compact molecular pi-pi stacking, which promotes carrier transport and suppresses bimolecular recombination. As a result, the best-performance OSC based on PM6:MDB delivered an outstanding PCE of 13.26%. In contrast, J71:MDB-based devices exhibited a lower PCE of 8.16%, due to the excessively high miscibility of J71 and MDB. As for P3HT:MDB-based devices, the poor miscibility between P3HT and MDB provides the driving force for the formation of large phase separation, which leads to an extremely low PCE of 0.45%. This work demonstrates that suitable miscibility is one of the key factors to achieve high-performance OSCs, which is an important guideline for the design and selection of next-generation photovoltaic materials.

N‐Doping Donor‐Dilute Semitransparent Organic Solar Cells to Weaken Donor: Acceptor Miscibility and Consolidate Donor‐Phase Continuity

Efficient Charge Transport Enables High Efficiency in Dilute Donor Organic Solar Cells.

Donor–acceptor mutually diluted heterojunctions for layer-by-layer fabrication of high-performance organic solar cells

Reducing the Excitonic Loss at Donor/Acceptor Heterojunction with Negligible Exciton Dissociation Driving Force

Effective N‐Doping of Non‐Fullerene Acceptor via Sequential Deposition Enables High‐Efficiency Organic Solar Cells

Regulating Crystallinity Mismatch Between Donor and Acceptor to Improve Exciton/Charge Transport in Efficient Organic Solar Cells

Synchronous Regulation of Donor and Acceptor Microstructure using Thiophene‐Derived Non‐Halogenated Solvent Additives for Efficient and Stable Organic Solar Cells

Oligomeric donor with appropriate crystallinity for organic solar cells

Boosting Fill Factor of Semitransparent Donor‐Poor Organic Solar Cells for the Best Light Utilization Efficiency

Reduced miscibility between highly compatible non-fullerene acceptor and donor enables efficient ternary organic solar cells

Building-up Relations between Intra- and Intermolecular Interactions, Miscibility, and Performance for Low-cost, Efficient Fully Non-fused Acceptor-based Organic Solar Cells

Molecular Doping Increases the Semitransparent Photovoltaic Performance of Dilute Bulk Heterojunction Film with Discontinuous Polymer Donor Networks

Thickness Insensitive Organic Solar Cells with High Figure‐of‐Merit‐X Enabled by Simultaneous D/A Interpenetration and Stratification

Enhanced Performance via End‐Group Alteration of Benzodithiophene‐Based Donors for Organic Solar Cells: a Theoretical Study

Trade‐Off Break Between the Crystallinity and Phase Separation of Donor/Acceptor via A General Two‐Dimensional Transition‐Metal Phosphorus Trichalcogenides Nanoparticle Dopant Concept for Efficient and Stable All‐Polymer Solar Cells

Donor End‐capped Alkyl Chain Length Dependent Non‐Radiative Energy Loss in All‐small‐molecule Organic Solar Cells

2D g‐C3N5 p‐Doping of Donor Material for High‐Efficiency Organic Solar Cells

Interfacial Molecular Doping at Donor and Acceptor Interface in Bilayer Organic Solar Cells

Regulating the Miscibility of Donors/acceptors to Manipulate the Morphology and Reduce Non-Radiative Recombination Energy Loss Enables Efficient Organic Solar Cells

Rationally Tuning Blend Miscibility of Polymer Donor and Nonfullerene Acceptor for Constructing Efficient Organic Solar Cells

Donor Polymer Can Assist Electron Transport in Bulk Heterojunction Blends with Small Energetic Offsets.