Whole-cell biocatalytic selective oxidation of 5-hydroxymethylfurfural to 5-hydroxymethyl-2-furancarboxylic acid

Xue-Ying Zhang,Min-Hua Zong,Ning Li

DOI: https://doi.org/10.1039/c7gc01751k

IF: 9.8

2017-01-01

Green Chemistry

Abstract:HMF has been efficiently upgraded into HMFCA with a good yield by using a highly HMF-tolerant strain Comamonas testosteroni SC1588.

chemistry, multidisciplinary,green & sustainable science & technology

What problem does this paper attempt to address?

Liquid-Phase Aerobic Oxidation of 5-Hydroxymethylfurfural to 2,5-Furandicarboxylic Acid over Co/Mn/Br Catalyst

Shuaibo Chen,Youwei Cheng,Heng Ban,Youdi Zhang,Liping Zheng,Lijun Wang,Xi Li

DOI: https://doi.org/10.1021/acs.iecr.0c01309

2020-01-01

Industrial & Engineering Chemistry Research

Abstract:2,5-Furandicarboxylic acid (FDCA), mainly synthesized by the selective oxidation of 5-hydroxymethylfurfural (HMF), is a biobased monomer for high-performance polymers. In this work, we have a comprehensive investigation on the rapid and highly selective oxidation process of HMF to FDCA in acetic acid (HAc) with Co/Mn/Br catalyst and air as the oxidant. It was found that both aldehyde and hydroxymethyl functional groups of HMF could be first oxidized in the sequential oxidation of HMF to FDCA, but 2,5-diformylfuran (DFF) was the main oxidation intermediate. Apart from the side reaction of HMF overoxidation to COx (CO and CO2) and HMF condensation to polymers, a small part of HMF will be further oxidized to maleic acid (MA) and fumaric acid (FA) via the ring-opening reactions under severe conditions because of the instability of furan ring. To reduce the side reactions and maximize the FDCA yield, the effects of temperature, pressure, substrate solvent ratio, catalyst composition and concentration, and water concentration on the main reactions and side reactions of the HMF oxidation were systematically evaluated. Under the optimum conditions, the selectivity of FDCA reached 92% with the total conversion of HMF in less than 20 min at a high mass ratio of substrate and solvent (1/9), and the purity of FDCA exceeded 99.8%. The experimental results provide a great reference and inspiration for the optimization of the HMF oxidation process and the large-scale production of FDCA.
Production of 2,5-Furandicarboxylic Acid by Optimization of Oxidation of 5-Methyl Furfural over Homogeneous Co/Mn/Br Catalysts

Heng Ban,Youdi Zhang,Shuaibo Chen,Youwei Cheng,Teng Pan,Lijun Wang,Xi Li

DOI: https://doi.org/10.1021/acssuschemeng.0c02574

IF: 8.4

2020-01-01

ACS Sustainable Chemistry & Engineering

Abstract:In this contribution, readily available 5-methyl furfural (MF) derived from biomass was used as an excellent substitute of the chemically unstable 5-hydroxymethylfurfural (HMF) for preparing the commercial precursor 2,5-furandicarboxylic acid (FDCA). MF was catalytically oxidized by air into FDCA in acetic acid over homogeneous Co/Mn/Br catalysts at 130-170 degrees C. It was found that both the substitute reactivity and the ring chemical stability have a remarkable impact on the yield of aromatic dicarboxylic acids. The effects of reaction temperature, pressure, catalyst composition and concentration, water concentration in the solvent, and substrate/solvent mass ratio on both the main reaction and the side reaction were investigated systematically and thoroughly using HPLC and an online tail gas monitoring system. Under optimized conditions, the oxidation of MF gave 100% conversion of MF and 75.8% yield of FDCA with 99.6% purity. It was also proven that the addition of 200 ppm cerium could work well at low temperatures (130-140 degrees C) for enhancing FDCA selectivity via suppressing the side reactions.
Selective 5-hydroxymethylfurfural production from cellulose formate in DMSO-H<sub>2</sub>O media

Caidi Jin,Ning Xiang,Xiao Zhu,E. Shuang,Kuichuan Sheng,Ximing Zhang

DOI: https://doi.org/10.1016/j.apcatb.2020.119799

2021-01-01

Abstract:5-hydroxymethylfurfural (HMF) can be widely converted into value-added chemicals and fuels production. Herein, we reported a sustainable and efficient approach for synthesizing HMF directly from cellulose. Facile formylation of cellulose with green and recyclable formic acid was developed for cellulose formate (CF) production. CF with special net-like structure and high degree of formyl substitution was prepared. The resultant CF exhibited excellent catalytic conversion and selectivity for HMF production comparable to monomeric glucose as reactant in dimethyl sulfoxide (DMSO)-H2O media. In our work, we presented molecular dynamics simulations to elaborate the preferential coordination of DMSO around formyl group, which promoted the solvation of formylated substrate in DMSO-H2O mixture, and the HMF yielded could be protected by DMSO without further degradation to levulinic acid or humins.
Highly Selective Oxidation Of 5-Hydroxymethylfurfural To 5-Hydroxymethyl-2-Furancarboxylic Acid By A Robust Whole-Cell Biocatalyst

Ran Cang,Li-Qun Shen,Guang Yang,Zhi-Dong Zhang,He Huang,Zhi-Gang Zhang

DOI: https://doi.org/10.3390/catal9060526

IF: 3.9

2019-01-01

Catalysts

Abstract:Value-added utilization of biomass-derived 5-hydroxymethylfurfural (HMF) to produce useful derivatives is of great interest. In this work, extremely radiation resistant Deinococcus wulumuqiensis R12 was explored for the first time as a new robust biocatalyst for selective oxidation of HMF to 5-hydroxymethylfuroic acid (HMFCA). Its resting cells exhibited excellent catalytic performance in a broad range of pH and temperature values, and extremely high tolerance to HMF and the HMFCA product. An excellent yield of HMFCA (up to 90%) was achieved when the substrate concentration was set to 300 mM under the optimized reaction conditions. In addition, 511 mM of product was obtained within 20 h by employing a fed-batch strategy, affording a productivity of 44 g/L per day. Of significant synthetic interest was the finding that the D. wulumuqiensis R12 cells were able to catalyze the selective oxidation of other structurally diverse aldehydes to their corresponding acids with good yield and high selectivity, indicating broad substrate scope and potential widespread applications in biotechnology and organic chemistry.
Significantly Improved Oxidation of Bio-Based Furans into Furan Carboxylic Acids Using Substrate-Adapted Whole Cells

Mao Wen,Xue-Ying Zhang,Min-Hua Zong,Ning Li

DOI: https://doi.org/10.1016/j.jechem.2019.04.025

IF: 13.1

2019-01-01

Journal of Energy Chemistry

Abstract:Furan carboxylic acids are important building blocks in polymer and fine chemical industries. In this work, a simple substrate adaptation strategy was applied to improve the catalytic performances of Comamonas testosteroni SC1588 cells for the synthesis of various furan carboxylic acids. It was found that biocatalytic synthesis of 5-hydroxymethyl-2-furancarboxylic acid(HMFCA) was substantially promoted by adding histidine and increasing cell concentrations. HMFCA was produced in a quantitative yield from200 m M HMF in 24 h. Besides, the HMFCA yields of 71%–81% were achieved with the substrate concentrations up to 250–300 m M. It was firstly found that 4-tert-butylcatechol(TBC), as the stabilizer present in HMF, exerted a significantly detrimental effect on whole-cell catalytic synthesis of HMFCA at high substrate concentrations(more than 130 m M). In addition, a variety of furan carboxylic acids such as2-furoic acid, 5-methyl-2-furancarboxylic acid and 5-methoxymethyl-2-furancarboxylic acid were synthesized with the yields up to 98%.
Efficient biotransformation of 5-hydroxymethylfurfural to 5-hydroxymethyl-2-furancarboxylic acid by a new whole-cell biocatalyst Pseudomonas aeruginosa PC-1

Xin Pan,Sihua Wu,Deshan Yao,Lian Liu,Lina Zhang,Zixuan Yao,Yan Pan,Siyuan Chang,Bingfeng Li

DOI: https://doi.org/10.1039/d0re00018c

2020-01-01

Abstract:An efficient HMFCA production strategy was developed using a new whole-cell biocatalyst from Pseudomonas aeruginosa PC-1.

chemistry, multidisciplinary,engineering, chemical
Efficient Synthesis of 5-Hydroxymethyl-2-furancarboxylic Acid by Escherichia Coli Overexpressing Aldehyde Dehydrogenases.

Xue-Ying Zhang,Xiao-Yang Ou,Yi-Jing Fu,Min-Hua Zong,Ning Li

DOI: https://doi.org/10.1016/j.jbiotec.2019.11.007

IF: 3.595

2020-01-01

Journal of Biotechnology

Abstract:Catalytic transformation of biomass-derived furans into value-added chemicals and biofuels has received considerable interest recently. In this work, aldehyde dehydrogenases (ALDHs) were identified from Comamonas testosteroni SC1588 for the oxidation of bio-based furans into furan carboxylic acids. Of the whole-cell biocatalysts constructed, Escherichia coli expressing a vanillin dehydrogenase (E. coli_CtVDH1) proved to be the best for the oxidation of 5-hydroxymethylfurfural (HMF). 5-Hydroxymethyl-2-furancarboxylic acid (HMFCA) was obtained in the yield of approximately 92 % within 12 h using this recombinant strain when the HMF concentration was up to 200 mM. In a fed-batch process, 292 mM of HMFCA was produced within 20.5 h, thereby providing a productivity as high as 2.0 g/L h. Other furan carboxylic acids were synthesized in the yields of 83-95%. Besides, the partially purified HMF was smoothly converted into HMFCA by this recombinant strain, with a 90% yield.
Redox-Switchable Biocatalyst for Controllable Oxidation or Reduction of 5-Hydroxymethylfurfural into High-Value Derivatives

Jiaxing Xu,Aiyong He,Bin Wu,Lei Hu,Xiaoyan Liu,Zhen Wu,Jun Xia,Jiming Xu,Shouyong Zhou

DOI: https://doi.org/10.1021/acsomega.0c02178

IF: 4.1

2020-07-27

ACS Omega

Abstract:Biocatalytic upgrading of biomass-derived 5-hydroxymethylfurfural (HMF) into high-value derivatives is of great significance in green chemistry. In this study, we disclosed the successful utilization of whole-cell <i>Paraburkholderia azotifigens</i> F18 for its switchable catalytic performance in the on-demand catalysis of HMF to different value-added derivatives, namely, selective reduction to 2,5-bis(hydroxymethyl)furan (BHMF) or oxidation to 5-hydroxymethyl-2-furancarboxylic acid (HMFCA). Based on the fine-tuning of biochemical properties, the biocatalyst can proceed an efficient hydrogenation reaction toward HMF with a good selectivity of 97.6% to yield the BHMF at 92.2%. Noteworthily, BHMF could be further oxidized to HMFCA and 2,5-furandicarboxylic acid (FDCA) by the whole cell. To realize the on-demand syntheses of HMFCA, the genes encoding HMF oxidoreductase/oxidase of whole-cell F18 were then deleted to prevent the further conversion of HMFCA to FDCA, which led to a 10-fold decrease of FDCA. Thus, an HMF conversion of 100% with an HMFCA yield of 98.3% was finally achieved by the engineered whole cell at a substrate concentration of 150 mM. Moreover, HMFCA synthesis was efficiently prepared with an excellent selectivity of 96.3% and a yield of 85.1% even at a high substrate concentration of up to 200 mM.This article has not yet been cited by other publications.

chemistry, multidisciplinary
Synergistic Chemo/biocatalytic Synthesis of 2,5-Furandicarboxylic Acid from 5-Hydroxymethylfurfural

Zi-Yue Yang,Mao Wen,Min-Hua Zong,Ning Li

DOI: https://doi.org/10.1016/j.catcom.2020.105979

IF: 3.51

2020-01-01

Catalysis Communications

Abstract:2,5-Furandicarboxylic acid (FDCA) is a promising bio-based chemical in polymer industry. In this work, we constructed an oxidative cascade for one-pot synthesis of FDCA from 5-hydroxymethylfurfural (HMF) by exploiting Comamonas testosteroni SC1588 cells and laccase-2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO) system. HMF was oxidized to 5-hydroxymethyl-2-furancarboxylic acid (HMFCA) by the cells at neutral pH. The HMFCA formation shifted pH of the reaction mixture to acidic range, which favored laccase-TEMPO catalytic oxidation. 5-Formyl-2-furancarboxylic acid derived from HMFCA via laccase-TEMPO catalysis was converted to FDCA by the cells. FDCA was obtained in an 87% yield within 36 h, providing a productivity of around 0.4 g/L h.
Highly Selective Oxidation of 5-HMF to HMFCA Via a Facile Pt-Ag Co-Catalytic Strategy

Ming-Kun Ke,Yuan Min,Shu-Chuan Mei,Hou-Wei Zeng,Zhao-Hua Wang,Tian-Wei Hua,Jie-Jie Chen,Gui-Xiang Huang,Han-Qing Yu

DOI: https://doi.org/10.1016/j.apcatb.2024.124431

2024-01-01

Abstract:5-Hydroxymethyl-2-furancarboxylic acid (HMFCA) is an important feedstock in chemical and pharmaceutical industries. Its production through aerobic conversion of 5-hydroxymethylfurfural (5-HMF) has promising prospects but is challenged by the over-oxidation. In this work, we develop a refined Pt-Ag co-catalytic strategy to tailor the selectivity of 5-HMF’s aerobic oxidation. By simple in situ addition of AgNO3 to the thermal catalytic system of Pt nanoparticles, the main products of 5-HMF oxidation could be shifted from 2,5-furandicarboxylic acid (FDCA) to HMFCA with an ultrahigh selectivity of over 99%. Density functional theory calculations demonstrate that such strategy could alter the HMFCA adsorption sites from Pt to Ag sites and prevent the oxidation of hydroxymethyl group. In addition, this strategy can be extended to other Ag species, such as AgCl, Ag2O and AgO. This work provides insights into the Pt-Ag synergistic catalysis and opens up a simple avenue to control the product selectivity for biomass refinement.
Selective Oxidation of 5-Hydroxymethylfurfural to 5-Formyl-2-furancar-boxylic Acid over a Fe-Anderson Type Catalyst

Jiajia Xu,Zhiguo Zhu,Ziliang Yuan,Ting Su,Yuchao Zhao,Wanzhong Ren,Zehui Zhang,Hongying Lu

DOI: https://doi.org/10.1016/j.jtice.2019.08.006

IF: 5.477

2019-01-01

Journal of the Taiwan Institute of Chemical Engineers

Abstract:5-Formyl-2-furancarboxylic acid (FFCA) is an important bio-blocks material, which has promising applications in synthesis, chemical intermediates, drugs, etc. However, the selective oxidation of 5-hydroxymethylfurfural (HMF) into FFCA seems very difficult, which has been rarely studied. In this study, we have developed a new method for the selective oxidation of HMF to FFCA over a Fe-Anderson type catalyst of Na3H6FeMo6O24 center dot 5H(2)O (abbreviated as FeMo6). The FeMo6 catalyst was prepared by the recrystallization method and systematically characterized by XRD, UV-vis, FT-IR, TG, ICP-AES, and XPS technologies. Mo5+ species and a large number of surface oxygen species were found to be close-knit associated with catalytic performances. The experiment found that the maximum FFCA yield can be obtained when n-methyl pyrrolidone (NMP) was used as the reaction solvent and the HMF and K2CO3 molar ratio was 0.5. Under the optimal conditions (HMF/ K2CO3/Catalyst = 1/0.5/0.08, T = 100 degrees C, 8 h), the oxidation of HMF over the FeMo6 catalyst could produce FFCA with a yield of 75% in the solvent of NMP. Most importantly, this catalyst was employed in this reaction under aerobic environment at atmospheric pressure, demonstrating a high catalytic activity. (C) 2019 Taiwan Institute of Chemical Engineers. Published by Elsevier B.V. All rights reserved.
Selective Synthesis of 2-Furoic Acid and 5-Hydroxymethyl-2-furancarboxylic Acid from Bio-Based Furans by Recombinant Escherichia Coli Cells

Sai-Sai Shi,Xue-Ying Zhang,Min-Hua Zong,Chuan-Fu Wang,Ning Li

DOI: https://doi.org/10.1016/j.mcat.2019.03.006

IF: 4.6

2019-01-01

Molecular Catalysis

Abstract:Upgradation of bio-based furans into chemicals and biofuels has received great interest recently. In this work, we reported selective synthesis of furan carboxylic acids from the corresponding aldehydes by recombinant Escherichia coli cells expressing 3-succinoylsemialdehyde-pyridine dehydrogenase (SAPDH) from Comamonas testosteroni SC1588. The effects of induction and reaction conditions on whole-cell catalytic oxidation of furfural (FF) were studied. High temperature induction resulted in decreased activities of recombinant cells, likely due to improper protein folding. Nonetheless, recombinant cells induced under high temperature enable the byproduct furfuryl alcohol to be faster re-oxidized into 2-furoic acid (FCA) than those induced under low temperature. So the yield and selectivity of FCA were improved significantly by using high temperature induction, at expense of slightly longer reaction periods. The activities of recombinant cells highly depended on pH. The tolerant levels of this recombinant strain toward FF and 5-hydroxymethylfurfural (HMF) were approximately 100 mM. FCA and 5-hydroxymethyl-2-furancarboxylic acid (HMFCA) were obtained with the yields of 95-98%. FCA of up to 147 mM was produced by a fed-batch strategy, in a quantitative yield. In addition, most aromatic aldehydes tested were transformed into the target carboxylic acids by this biocatalytic method, with the yields up to 100%.
Efficient synthesis of 5-hydroxymethyl-2-furancarboxylic acid from bio-based high-concentration 5-hydroxymethylfurfural via highly tolerant aldehyde dehydrogenase

Siyuan Chang,Sen Zhang,Tianyi Chen,Lei Xu,Sumin Ge,Bingfeng Li,Chenke Yun,Guoxin Zhang,Xuejun He,Xin Pan

DOI: https://doi.org/10.1016/j.mcat.2023.112966

IF: 4.6

2023-02-02

Molecular Catalysis

Abstract:The important bio-based platform chemical 5-Hydroxymethylfurfural (HMF) can be oxidized for use in several products that serve as versatile building blocks of polymers. Previously, we had demonstrated that Pseudomonas aeruginosa PC-1 can selectively produce 5-hydroxymethyl-2-furancarboxylic acid (HMFCA) from 800 mM HMF, with a yield greater than 90%. In this study, an aldehyde dehydrogenase (PaALDH64) was identified from P. aeruginosa PC-1 for selective HMF oxidation to HMFCA. The HMF tolerance level of E. coli /pET- PaALDH64 was over 300 mM, which was greater than the tolerance levels of all other reported enzymes. The proposed biocatalyst could be used to catalyze the biotransformation of other aldehydic furans, with carboxylic acid yields over 92%. Molecular docking revealed that the catalytic active site cleft in PaALDH64 formed more hydrogen bonds with HMF compared to other enzymes, which stabilized the enzyme–substrate interaction and enhanced the catalytic efficiency. In a fed-batch process, 547.8 mM HMFCA was produced from 600 mM HMF by E. coli /pET- PaALDH64 within 19 h only, which showed an excellent HMF conversion rate. Overall, PaALDH64 constitutes a promising enzyme for the industrial production of HMFCA.

chemistry, physical
Biocatalytic Reduction of HMF to 2,5‐bis(hydroxymethyl)furan by HMF‐Tolerant Whole Cells

Yanmei Li,X. Peter Zhang,Ning Li,Pei Xu,Wen‐Yong Lou,Min‐Hua Zong

DOI: https://doi.org/10.1002/cssc.201601426

IF: 8.4

2016-01-01

ChemSusChem

Abstract:Catalytic upgrading of 5‐hydroxymethylfurfural (HMF), an important biobased platform chemical for high‐value products, is currently of great interest. In this work, a new highly HMFtolerant yeast strain— Meyerozyma guilliermondii SC1103 was isolated, and biocatalytic reduction of HMF to 2,5‐bis(hydroxymethyl)furan (BHMF) using its resting cells was reported. Cosubstrates exerted a significant effect on the catalytic activity and selectivity of microbial cells as well as their HMF‐tolerant levels whereas the nitrogen source and mineral salts had no effects. In addition, M. guilliermondii SC1103 cells exhibited good catalytic performances within the range of pH 4.0–10.0. The yeast was highly tolerant to both HMF (up to 110 m m ) and BHMF (up to 200 m m ). In addition, 100 m m HMF could be selectively reduced to BHMF within 12 h by its resting cells in the presence of 100 m m glucose (as cosubstrate), with a yield of 86 % and selectivity of >99 %. The production of 191 m m of BHMF was realized within 24.5 h by using a fed‐batch strategy, with a productivity of approximately 24 g L −1 per day. In addition, this new biocatalytic approach was applied for the reduction of furfural and 5‐methylfurfural, affording the corresponding furfuryl alcohols with yields of 83 and 89 %, respectively.
Efficient Reduction of 5-Hydroxymethylfurfural to 2, 5-Bis (hydroxymethyl) Furan by a Fungal Whole-Cell Biocatalyst

Dong Chen,Ran Cang,Zhi-Dong Zhang,He Huang,Zhi-Gang Zhang,Xiao-Jun Ji

DOI: https://doi.org/10.1016/j.mcat.2020.111341

IF: 4.6

2021-01-01

Molecular Catalysis

Abstract:Biocatalytic reduction of biomass-derived 5-hydroxymethylfurfural (HMF) to 2,5-bis(hydroxymethyl)furan (BHMF) is considered as a sustainable method and has attracted great attention. In this work, a yeast-like fungus, Aureobasidium subglaciale F134 was discovered as a whole-cell biocatalyst for BHMF synthesis from selective reduction of HMF. Its resting cells exhibited high tolerance and excellent selectivity to HMF in a broad pH range. The catalytic capacity of the cells can be substantially improved by Zn2+ ion. Under the optimized reaction conditions, 180 mM HMF substrate was converted into BHMF with a yield of 82 % and 97 % selectivity in 9 h. In a fed-batch conversion, 430 mM of BHMF product was obtained within 15 h, giving a productivity of 3.7 g/l per hour. In addition, it was found that the cells could also selectively convert furfural to form furfuryl alcohol. Discovery of A. subglaciale F134 cells for BHMF synthesis broadens the biocatalyitc toolbox for sustainable production of bio-based chemicals and biofuels from biomass-derived HMF. In addition, the results provide more information regarding the identification of related enzymes in future work.
Sustainable Approaches to Selective Conversion of Cellulose Into 5-Hydroxymethylfurfural Promoted by Heterogeneous Acid Catalysts: A Review

Yuanyong Yao,Shixue Chen,Meng Zhang

DOI: https://doi.org/10.3389/fchem.2022.880603

IF: 5.5

2022-05-11

Frontiers in Chemistry

Abstract:5-Hydroxymethylfurfural (5-HMF) as a triply catalytic product is a value-added refining chemical in industry production. 5-HMF as biomass feedstock enables to be transformed into other high-value industrial compounds, such as 2,5-furandicarboxylic acid (FDCA), 5-hydroxymethyl-2-furancarboxylic acid (HMFCA), 5-formyl-2-furancarboxylic acid (FFCA), 2,5-diformylfuran (DFF), 2,5-bis(aminomethyl)furan (BAMF), and 2,5-dimethylfuran (DMF). Hence, catalytic conversion of biomass into 5-HMF has been given much more attention by chemists. In this review, some latest studies about the conversion of cellulose to 5-HMF have been introduced systematically. Solid acids such as heterogeneous catalysts have been widely applied in the conversion of cellulose into 5-HMF. Therefore, some novel solid acids with Brønsted and/or Lewis acidic sites, such as sulfonated solid acids, carbon-based acids, and zeolite particles employed for biomass conversions are listed.

chemistry, multidisciplinary
Biocatalytic Oxidation of Biobased Furan Aldehydes: Comparison of Toxicity and Inhibition of Furans Toward a Whole-Cell Biocatalyst

Ai-Di Cheng,Sai-Sai Shi,Yao Li,Min-Hua Zong,Ning Li

DOI: https://doi.org/10.1021/acssuschemeng.9b05621

IF: 8.4

2019-01-01

ACS Sustainable Chemistry & Engineering

Abstract:Furan carboxylic acids are promising and renewable building blocks in polymer and pharmaceutical industries. In this work, biocatalytic synthesis of furan carboxylic acids was performed from biobased furan aldehydes using recombinant Escherichia coli expressing 3-succinoylsemialdehyde-pyridine dehydrogenase (SAPDH). Particularly, the inhibition and toxicity of furan aldehydes and their carboxylic acid derivatives toward this whole-cell biocatalyst were evaluated. It was found that this biocatalyst displayed the highest tolerance level (200 mM) toward 5-hydroxymethylfurfural (HMF) in the oxidation of furan aldehydes, lower toward 5-methoxymethylfurfural (MMF, 150 mM), and the lowest (75 mM) toward furfural. This may be explained by the less detrimental effects of high concentrations of HMF on the biocatalyst which might be closely related to the low hydrophobicity of this substance. In addition, the presence of furan carboxylic acids resulted in the substantial decrease in both catalytic activities and viability of the cells. The inhibition and toxicity of furan carboxylic acids toward the cells were greatly relieved upon neutralization with a base. Based on the results obtained above, a combined reaction engineering strategy (fed-batch operation coupled with pH controlling) was designed for efficient synthesis of 5-methoxymethyl-2-furancarboxylic acid (MMFCA) from MMF. In addition, the gram-scale preparation of MMFCA was implemented. The desired product was obtained in an isolated yield of 89% and a purity of >98%. Its space-time yield was up to 1.2 g/L h.
Advances in Selective Conversion of Carbohydrates into 5-Hydroxymethylfurfural

Jie Liang,Jianchun Jiang,Tingting Cai,Chao Liu,Jun Ye,Xianhai Zeng,Kui Wang

DOI: https://doi.org/10.1016/j.gee.2023.11.005

IF: 12.781

2024-01-01

Green Energy & Environment

Abstract:Converting carbohydrates into 5-hydroxymethylfurfural (5-HMF) is an attractive and promising route for value-added utilization of agricultural and forestry biomass resource. As an important platform compound, 5-HMF possesses high active furan structure with hydroxymethyl and aldehyde group for production of various bio-chemicals and materials, meanwhile, which suffer from low stability and poor yield during the industrial biorefinery process. Hence, selective production of 5-HMF with high-yield and low-cost has attracted extensive attention from scientific and industrial researchers. This review sorted and described the latest advanced research on solvent and catalyst system, as well as energy field effect for production of 5-HMF with different feedstock in detail, emphatically discussing the solvent effect and its synergistic effect with other aspects. Besides, the future prospects and challenges for production of 5-HMF from carbohydrates were also presented, which provide a profound insight into industrial 5-HMF process with economic and environmental feature.
Selective Oxidation of 5-Formyloxymethylfurfural to 2, 5-Furandicarboxylic Acid with Ru/C in Water Solution

Zhihao Si,Xin Zhang,Miao Zuo,Tao Wang,Yong Sun,Xing Tang,Xianhai Zeng,Lu Lin

DOI: https://doi.org/10.1007/s11814-019-0422-8

IF: 2.7

2020-01-01

Korean Journal of Chemical Engineering

Abstract:2, 5-furandicarboxylic acid (FDCA) is a one of the most promising biomass-derived chemicals to substitute the non-renewable terephthalic acid as the monomer for producing polyethyleneterephthalate. At present, the oxidation of HMF is regarded as a prevalent way to prepare FDCA. Nevertheless, the isolation and storage of HMF is still a challenge. Herein, based on the higher stability of 5-formyloxymethylfurfural (FMF) than 5-hydroxymethylfurfural (HMF), we present an effective preparation route to prepare FDCA by substituting HMF with FMF as feedstock. A complete conversion of FMF and a 93.55% selectivity of FDCA were obtained in the mixed solvent of water and 1, 2-dioxane using Ru/C as catalyst and O-2 as oxidant. An improved process was developed for preparing FDCA using FMF as feedstock. The investigation of conversion pathway showed that FMF and HMF were simultaneously oxidized to 2, 5-diformylfuran (DFF) in a case of the existence of the reversible equilibrium between FMF and HMF. Then DFF was oxidized to 5-formyl-2-furancarboxylic acid (FFCA). Subsequently, FFCA was oxidized to FDCA. In this process, the oxidation of FFCA to FDCA was determined as the rate-determining step. Furthermore, appropriate alkalinity favored the selectivity of FDCA and the conversion of FMF.
Sacrificial Substrate-Free Whole-Cell Biocatalysis for the Synthesis of 2,5-Furandicarboxylic Acid by Engineered Escherichia Coli

Xin Wang,Xue-Ying Zhang,Min-Hua Zong,Ning Li

DOI: https://doi.org/10.1021/acssuschemeng.0c00058

IF: 8.4

2020-01-01

ACS Sustainable Chemistry & Engineering

Abstract:2,5-Furandicarboxylic acid (FDCA) is a promising biobased building block for the synthesis of polymers. In this work, a novel whole-cell biocatalyst was constructed by coexpressing vanillin dehydrogenase (VDH1) and HMF/furfural oxidoreductase (HmfH) in Escherichia coli for cascade catalytic oxidation of 5-hydroxymethylfurfural (HMF) to FDCA under sacrificial substrate-free conditions. HMF was rapidly transformed to 5-hydroxymethyl-2-furancarboxylic acid (HMFCA) by VDH1, followed by subsequent oxidation to 5-formyl-2-furancarboxylic acid (FFCA) by HmfH, and finally, FFCA was converted to FDCA by VDH1 and/or HmfH. Under pH-controlled conditions, the biocatalyst enabled efficient synthesis of FDCA from 150 mM HMF in a 96% yield. Besides, FDCA was prepared in the gram scale with a productivity of around 0.4 g/L h.

Whole-cell biocatalytic selective oxidation of 5-hydroxymethylfurfural to 5-hydroxymethyl-2-furancarboxylic acid

Liquid-Phase Aerobic Oxidation of 5-Hydroxymethylfurfural to 2,5-Furandicarboxylic Acid over Co/Mn/Br Catalyst

Production of 2,5-Furandicarboxylic Acid by Optimization of Oxidation of 5-Methyl Furfural over Homogeneous Co/Mn/Br Catalysts

Selective 5-hydroxymethylfurfural production from cellulose formate in DMSO-H<sub>2</sub>O media

Highly Selective Oxidation Of 5-Hydroxymethylfurfural To 5-Hydroxymethyl-2-Furancarboxylic Acid By A Robust Whole-Cell Biocatalyst

Significantly Improved Oxidation of Bio-Based Furans into Furan Carboxylic Acids Using Substrate-Adapted Whole Cells

Efficient biotransformation of 5-hydroxymethylfurfural to 5-hydroxymethyl-2-furancarboxylic acid by a new whole-cell biocatalyst Pseudomonas aeruginosa PC-1

Efficient Synthesis of 5-Hydroxymethyl-2-furancarboxylic Acid by Escherichia Coli Overexpressing Aldehyde Dehydrogenases.

Redox-Switchable Biocatalyst for Controllable Oxidation or Reduction of 5-Hydroxymethylfurfural into High-Value Derivatives

Synergistic Chemo/biocatalytic Synthesis of 2,5-Furandicarboxylic Acid from 5-Hydroxymethylfurfural

Highly Selective Oxidation of 5-HMF to HMFCA Via a Facile Pt-Ag Co-Catalytic Strategy

Selective Oxidation of 5-Hydroxymethylfurfural to 5-Formyl-2-furancar-boxylic Acid over a Fe-Anderson Type Catalyst

Selective Synthesis of 2-Furoic Acid and 5-Hydroxymethyl-2-furancarboxylic Acid from Bio-Based Furans by Recombinant Escherichia Coli Cells

Efficient synthesis of 5-hydroxymethyl-2-furancarboxylic acid from bio-based high-concentration 5-hydroxymethylfurfural via highly tolerant aldehyde dehydrogenase

Biocatalytic Reduction of HMF to 2,5‐bis(hydroxymethyl)furan by HMF‐Tolerant Whole Cells

Efficient Reduction of 5-Hydroxymethylfurfural to 2, 5-Bis (hydroxymethyl) Furan by a Fungal Whole-Cell Biocatalyst

Sustainable Approaches to Selective Conversion of Cellulose Into 5-Hydroxymethylfurfural Promoted by Heterogeneous Acid Catalysts: A Review

Biocatalytic Oxidation of Biobased Furan Aldehydes: Comparison of Toxicity and Inhibition of Furans Toward a Whole-Cell Biocatalyst

Advances in Selective Conversion of Carbohydrates into 5-Hydroxymethylfurfural

Selective Oxidation of 5-Formyloxymethylfurfural to 2, 5-Furandicarboxylic Acid with Ru/C in Water Solution

Sacrificial Substrate-Free Whole-Cell Biocatalysis for the Synthesis of 2,5-Furandicarboxylic Acid by Engineered Escherichia Coli