Abstract:Four different thin film nanocomposite (TFN) membranes were prepared by adding different concentrations of porous Zr-MOFs (UiO-66 and UiO-66-NH2) to piperazine (PIP) aqueous solution (aqueous phase) or 1,3,5-Benzenetricarbonyl trichloride (TMC)-n-hexane solution (organic phase) by interfacial polymerization. The main purpose is to study the specific effects of different addition methods and addition amounts of nanoparticles on the structure and performance of the TFN membranes by interfacial polymerization. All four TFN membranes exhibited higher water permeability while maintaining high salt rejection compared to thin film composite (TFC) membrane. On the one hand, the TFN membranes behaves differently which are prepared by adding the same kind of nanoparticles to the aqueous phase or organic phase, respectively. The TFN membrane prepared by adding 0.2 w/v% UiO-66 to the organic phase had high water flux of 87.86 L·m-2·h-1, comparing 46.31 L·m-2·h-1 of membrane prepared by adding 0.3 w/v% UiO-66 in the aqueous phase. This is due to the fact that UiO-66 greatly slows the interfacial polymerization rate when UiO-66 is added to the organic phase, resulting in a thinner and more aperture polyamide thin film layer, reducing the water transmission resistance during filtration. Therefore, it is more economical by adding nanoparticles to organic phase than aqueous phase under the same filtering effect. On the other hand, different nanoparticles can also cause differences in performance and structure of the TFN membranes even in the same preparation manner. TFN membrane with UiO-66-NH2 in the aqueous phase has higher water permeance than the one with UiO-66 in the aqueous phase, owning to good hydrophilicity of amino group, which improves the water dispersibility of UiO-66-NH2, so that the TFN membrane is more uniform. In addition, UiO-66-NH2 slows down the process of interface polymerization, making the membrane more porous. The monomers in aqueous phase and the organic phase can be adsorbed in the pores of Zr-MOFs, which makes the interfacial polymerization occur both in the pores and on the surface of the pores. Thus, the compatibility between the polyamide and MOFs was enhanced and less defects was formed in the thin film layer, resulting in high salt rejection even the concentration of Zr-MOFs increased. This is the first time to explain that polyamide membrane has not obvious salt rejection attenuation with increasing porous material content using pore adsorption reaction monomer principle. Also, the Zr-MOFs based TFN membrane exhibited good heat resistance and anti-fouling property. This work shows that porous Zr-MOFs nanomaterials have significant advantages in the development of nanofiltration membranes with high water flux and rejection.

MOF laminates functionalized polyamide self-cleaning membrane for advanced loose nanofiltration

Hydrophilic Modified Polydopamine Tailored Heterogeneous Polyamide in Thin-Film Nanocomposite Membranes for Enhanced Separation Performance and Anti-Fouling Properties

MOF-808/Polyamide Thin-Film Nanocomposite Membranes for Efficient Nanofiltration

Engineering polyamide nanofiltration membrane with bifunctional terpolymer brushes for antifouling and antimicrobial properties

Custom-tailoring metal-organic framework in thin-film nanocomposite nanofiltration membrane with enhanced internal polarity and amplified surface crosslinking for elevated separation property

PolyMOF Interlayers Modulated Interfacial Polymerization of Ultra-thin Nanofiltration Membranes with Efficient and Stable Desalination Performance

High-performance zwitterionic TFC polyamide nanofiltration membrane based on a novel triamine precursor

Development of high permeability nanofiltration membranes through porous 2D MOF nanosheets

In-situ incorporating zwitterionic nanocellulose into polyamide nanofiltration membrane towards excellent perm-selectivity and antifouling performances

A novel loose nanofiltration membrane with high permeance and anti-fouling performance based on aqueous monomer piperazine-2-carboxylic acid for efficient dye/salt separation

Molecular Design of the Polyamide Layer Structure of Nanofiltration Membranes by Sacrificing Hydrolyzable Groups Toward Enhanced Separation Performance.

Porous Zr-based metal organic frameworks (Zr-MOFs) incorporated thin film nanocomposite membrane toward enhanced desalination performance.

Thin film composite membrane with self-cleaning properties via a catalytic interlayer for dye wastewater treatment

Fabrication of polyamide nanofiltration membrane with tannic acid/poly(sodium 4-styrenesulfonate) network-like interlayer for enhanced desalination performance

Enhancing the perm-selectivity of thin-film nanocomposite membranes intercalated with cyclodextrin-chelated Metal-Organic Framework via modulated interfacial polymerization

Thin-film nanocomposite membranes containing tannic acid-Fe3+ modified MoS2 nanosheets with enhanced nanofiltration performance

In Situ Chemical Modification with Zwitterionic Copolymers of Nanofiltration Membranes: Cure for the Trade-Off between Filtration and Antifouling Performance

Interface Engineering of Microporous Polypropylene Membranes for Polyamide Thin-Film Composite Nanofiltration Membranes with Robust Structure and Superior Performance

Designing a multifunctional TFC membrane with improved permeability and anti-biofouling performance using zwitterionic, quaternary ammonium, and fluorinated materials

Nanofiltration Membranes with Hydrophobic Microfiltration Substrates for Robust Structure Stability and High Water Permeation Flux

Codeposition of Catechol–polyethyleneimine Followed by Interfacial Polymerization for Nanofiltration Membranes with Enhanced Stability