Abstract:Abstract The reliability and safety of aero-engine are often the decisive factors for the safe and reliable flight of commercial aircraft. Hence, the vibration source location and fault diagnosis of aero-engine are of prime importance to detect faults and carry out fast and effective maintenance in time. However, the vibration signals collected by the sensors arranged on the casing of the aero-engine are generally the mixed signals of the main vibration sources inside the engine, and the components are extremely complicated. Therefore, the vibration source identification is a big challenge for a fault diagnosis and health management of the engine. In order to separate the key vibration sources of rotating machinery such as aero-engine, a Joint Wavelet Transform and Time Synchronous Averaging based algorithm (JWTS) is proposed in this paper. Based on the fact that the fundamental frequency and its harmonic and sub-harmonic components are generally included in the vibration spectrum of shaft fault signal of rotating machinery, wavelet transform and time synchronous averaging algorithm are combined to extract them. The algorithm completes separating the main vibration sources with three steps. First, the source number and fundamental frequency of each source are estimated using the wavelet transform. Second, every source is extracted from each observed signal by the time synchronous averaging method. Time synchronous averaging method can effectively extract a signal of cycle and harmonic rotor components and can suppress noise. Third, the optimal estimation of each source is determined according to signal’s 2-norm. Since the extracted source with a larger energy is closer to the real source, and signal’s 2-norm is a good indicator of the signal energy. Hence, the key vibration sources related to rotary speeds of the engine are obtained separately. The method is verified by synthetic mixed signals first. Three periodic signals of different frequencies are used to simulate the vibration sources of the aeroengine. The fundamental, harmonic and sub-harmonic components of them, as well as Gaussian white noise, are randomly mixed. The results show that the JWTS algorithm can estimate the number of the main sources and can extract each source effectively. Then the method is demonstrated using vibration signals of a real aero-engine. The results indicate that the proposed JWTS method has extracted and located the main sources within the aero-engine, including sources from the low-pressure rotor, high-pressure rotor, combustion chamber and accessory. Therefore, the proposed method provides a new fault diagnosis technology for rotating machinery, especially for a real aero-engine.

Identification and separation of coupled vibration sources in multi-rotor gas turbines under time-varying speed conditions

Research On Control Technologies For A High-Precision Multi-Source Vibration Simulation System

Single-tone Aerodynamic Noise Source Separation for Gas Turbines

Joint Wavelet Transform and Time Synchronous Averaging Source Separation Method and its Application on Aero-Engine

A Study on Vibration Component Separation of a Rotor System During Startup and Its Application in Fault Diagnosis

Blind Vibration Sources Separation Method Based on Signal Feature of Aircraft Engine

Multicomponent collaborative time-frequency state-space model for vibration signal decomposition under nonstationary conditions

An Operating Condition Information-Guided Iterative Variational Mode Decomposition Method Based on Mahalanobis Distance Criterion for Surge Characteristic Frequency Extraction of the Centrifugal Compressor

Convolutive blind source separation in the frequency domain of mechanical noise for gas turbines based on bounded component analysis

Vold-Kalman Generalized Demodulation For Multi-Faults Detection Of Gear And Bearing Under Variable Speeds

Multiscale Filtering Reconstruction for Wind Turbine Gearbox Fault Diagnosis Under Varying-Speed and Noisy Conditions

Application of Variational Mode Decomposition to Feature Isolation and Diagnosis in a Wind Turbine

Sparse Component Analysis-Based Under-Determined Blind Source Separation for Bearing Fault Feature Extraction in Wind Turbine Gearbox

Identification of Torsional Modal Parameters Based on Excitation-Injection Tests on Turbine-Generators

Vibration Propagation Identification of Rotor-Bearing-casing System Using Spatiotemporal Graphical Modeling

Digital Simulation of Coupled Dynamic Characteristics of Open Rotor and Dynamic Balancing Test Research

Design and test of adaptive torsional vibration suppression method for helicopter power system with variable rotor speed

Diagnosis of non-linear mixed multiple faults based on underdetermined blind source separation for wind turbine gearbox: simulation, testbed and realistic scenarios

A Dichotomy-Based Variational Mode Decomposition Method for Rotating Machinery Fault Diagnosis

Analysis of Vibration Characters of Excitation Sources in Gas Turbine Rotor Systems

Blind Separation of Vibration Sources using Deep Learning and Deconvolution