Abstract:Adiabatic shear band (ASB), a typical failure mechanism in a metal at high strain rates, is hardly controllable or predictable to some extent. The development of the microstructure plays a crucial role in its formation. In this paper, the effect of strain rate on the development of microstructure in ASB of titanium alloy TC4 is investigated using hat-shaped specimens with the split-Hopkinson pressure bar device. The results show that the fracture strength of TC4 is significantly dependent on the shear strain rate. The increase in fracture strength from a strain rate of 11,300 s −1 to 24,930 s −1 is much higher than that from 24,930 s −1 to 35,620 s −1 , which can be attributed to the effect of strain rate on dislocation evolution. Microstructures in both as-received and deformed states are investigated using various characterization techniques such as electron backscatter diffraction and X-ray diffraction. The region of ASB clearly shows three different microstructural features: random distribution of coarse grains (as received), distribution of elongated grains (transition zone), and distribution of equiaxed nanocrystals (shear-localized zone). The width of ASB increases with the strain rate. The possible reason for this is that the higher the strain rate, the larger the region where dynamic recrystallization (DRX) occurs due to the accumulation of a large number of dislocations. In the middle of ASB, a significant decrease in low-angle grain boundaries (LAGBs) and a large increase in high-angle grain boundaries are observed. The texture of specimens, especially the {11–20} and {10–10} planes, changes significantly during shear deformation at high strain rates. The mechanism of continuous dynamic recrystallization can well explain the formation and evolution of DRX within the ASB.

Significance of Strain Rate in Severe Plastic Deformation on Steady-State Microstructure and Strength

The effect of strain rate on the evolution of microstructure in aluminium alloys

New Insight for Mechanical Properties of Metals Processed by Severe Plastic Deformation

Effect of Strain Rate and Temperature on Dynamic Mechanical Behavior and Microstructure Evolution of Ultra-High Strength Aluminum Alloy

Strain Rate and Anisotropic Effects on Incipient Plastic Deformation of Zn–Cu–Ti Alloy Sheets

Constitutive Modelling of Plasticity of Fcc Metals under Extremely High Strain Rates

High Strain Rate Superplasticity in Al-Zn-Mg-Based Alloy: Microstructural Design, Deformation Behavior, and Modeling

Strain Rate Dependence of Strengthening Mechanisms in Ultrahigh Strength Lath Martensite

Effect of Strain Rate on Microstructure and Mechanical Properties of Electroplastic Rolled ZrTi Alloy

Effects of Strain and Strain Rates on Microstructure Evolution Within ASB of TC4

Strain effects on the wear rate of severely deformed copper

Effect of strain rate on microstructure evolutions and mechanical properties of cryorolled Zr upon annealing

A rate-dependent damage mechanics model for predicting plasticity and ductile fracture behavior of sheet metals at high strain rates

Strain hardening, strain rate sensitivity, and ductility of nanostructured metals

Strain Rate Effect on Plastic Deformation of Nanocrystalline Copper Investigated by Molecular Dynamics

Molecular Dynamics as a Means to Investigate Grain Size and Strain Rate Effect on Plastic Deformation of 316 L Nanocrystalline Stainless-Steel

Influence of Strain Rate on Tensile Characteristics of Sus304 Metastable Austenitic Stainless Steel

Strain Rate Sensitivity of Low‐Temperature Superplastic Heterogeneous Medium‐Mn Steel Fabricated by a Novel High‐Ratio Differential Speed Rolling

On the Grain Size Dependent Working Hardening Behaviors of Severe Plastic Deformation Processed Metals

Strain-Rate-Dependent Deformation Behavior of Ti29Zr24Nb23Hf24 High Entropy Alloys at Elevated and Room Temperature

Fracture behavior of a rapidly solidified thin-strip continuous cast AA5182 Al-Mg alloy with the Portevin-Le Chatelier effect under varying strain rates