Abstract:s The paper uses a laser cladding process to prepare a composite coating of Ni60A and x% TiC (x = 0, 2, 4, 8) by mass percentage on the surface of H13 steel. The effects of different TiC additions on the microstructure and properties of the laser cladding coatings were analyzed by X-ray diffractometer (XRD), non-destructive testing, Penetrant testing (PT), optical microscope (OM), scanning electron microscope (SEM), energy dispersive spectrometer (EDS), micro-hardness tester, friction and wear tester, and electrochemical workstation. The results show that the coating microstructure without TiC addition was dominated by dendrites. The microstructure of the coatings appeared as short rods and equiaxed crystals after the addition of TiC. After analysis, hard reinforcing phases such as Cr 23 C 6 , Cr 7 C 3 , and TiCx were found to have a pinning effect at the grain boundaries, thus hindering the grain boundary slip. These can significantly increase the hardness of the coating. Most of the Ni60A coating with the addition of 2 wt% TiC (C2)coating curve is at the bottom end of the graph line. It has an average friction factor of 1.43 and a low wear weight loss. C2 coatings have less wear than C0 coatings.C2 coatings have 8.5% of the wear of C0 coatings.C2 has the best wear resistance. The hardness of the C2 coating is 662HV0.5, which is higher than other coatings with different TiC additions. The C2 coating had the lowest self-corrosion current of 7.076 ×10–7 A·cm-2. C2 coatings significantly appear grain refinement, lattice distortion, coating hardness, and wear resistance are high, with better corrosion resistance. The strengthening mechanism is mainly solid solution strengthening and fine grain strengthening together.

Mechanical properties of TiC-reinforced H13 steel by bionic laser treatment

Microstructure and Wear-resistant Properties of in situ TiB-TiC Reinforced Titanium Matrix Composites by Laser Deposition Manufacturing

Coarse TiC particles reinforced H13 steel matrix composites produced by laser cladding

Microstructure manipulation mechanism and mechanical properties improvement of H13 steel via trace nano-(TiC + TiB2) particles

Effect of TiC addition on the microstructure and properties of laser cladding Ni60A coatings on H13 steel surface

Effect of Cryogenic Treatment on the Microstructure and Mechanical Properties of Selected Laser Melted H13 Steel

Microstructure and wear resistance of laser-clad Ni60-Ti-B4C coatings

Microstructure and mechanical properties of in-situ hybrid reinforced (TiB+TiC)/Ti composites prepared by laser powder bed fusion

Role and mechanism of innovative addition process of trace nano-TiC p in microstructure manipulation and significant mechanical properties enhancement of H13 steels

Study on fabrication of multi-phase reinforcement coatings on Ti6Al4V by laser cladding for enhanced tribological performance

Effect of in-situ grown TiC on microstructure and tribological performance of laser cladded NiCrAl-40 %WC coating by addition of Ti

In-situ TiB2-TiC reinforced Fe-Al composite coating on 6061 aluminum alloy by laser surface modification

Microstructure and tribological properties of laser cladded TiC reinforced WC-10Co4Cr coatings at 500 °C

Effect of TiB 2 content on microstructure and mechanical properties of GH3536 superalloy formed by laser solid forming

Microstructure and anti-ablation of laser cladding Ti-Zr-B-C coating on TC11 titanium alloy

Effects of Process Parameters on Geometrical Characteristics and Microstructure of TiC Particle-Reinforced Co50 Alloy by Laser Cladding

Influence of laser treatment on the microstructural evolution and performance of Ti65 alloy

Engineering fine grains, dislocations and precipitates for enhancing the strength of TiB 2 -modified CoCrFeMnNi high-entropy alloy using Laser Powder Bed Fusion

Achieving near equiaxed α-Ti grains and significantly improved plasticity via heat treatment of TiB reinforced titanium matrix composite manufactured by selective laser melting

Effect of TiB 2 on the microstructure and mechanical properties of TiAl alloy produced by laser direct energy deposition

Effect of TiB2 Addition on the Microstructure and Mechanical Properties of Laser-Directed Energy Deposition TiAl Alloy