Abstract:Despite boasting giant leaps in performance improvement over the years, the current commercial standard, Li-ion batteries, are fast approaching their theoretical limits. Meanwhile, Lithium-Sulfur (Li-S) batteries offering ultra-high theoretical energy density (~2600 Whkg -1 ), cost-effectiveness, and nontoxicity are being seen as promising alternatives. Despite their plentiful advantages, the practicality of Li-S batteries has been largely stymied by several challenges: a) deleterious polysulfide dissolution and ‘shuttle effect’, b) significant volume change of S cathodes during cycling, c) safety concerns with flammable traditional glyme-based electrolyte, and d) the instability of Li anode. To mitigate these challenges, researchers have explored all-solid-state electrolytes, but their poor Li-ion conductivity, high interfacial impedance, and need for expensive, exotic materials and complex fabrication procedures severely limit their practical application. To overcome these challenges, we propose an in-situ gelled polymer-ceramic hybrid silsesquioxane-based electrolyte system. The gelled matrix, thermally crosslinked post cell fabrication, immobilizes the glyme-based liquid electrolyte and exhibits high liquid-like ionic conductivities (1.03 mS.cm -1 ), low interfacial impedance, and high oxidative potential (>4.5V vs. Li/Li + ) . In this study, in addition to vastly decreased flammability, we report superior Li-ion conductivity compared to state-of-art solid-state Li-S electrolytes. This high ionic conductivity translated to a significantly improved specific capacity of 1050 mAh.gS -1 at 0.2 C, elevated Coulombic efficiencies (>98.5%), and elevated rate kinetics. The gelled electrolytes exhibited stable cycling in a large temperature range (-10 o C - 60 o C). Moreover, polysulfide permeation studies and subsequent DFT calculations revealed that the gelled electrolyte exhibited strong chemical absorptivity to lithium polysulfides due to the polar silsesquioxane core, which translated to superior capacity retention (>80% over 200 cycles). Further, post- mortem XPS characterization studies revealed the formation of stable SEI at the anode and cathode, and SEM of cycled anodes showed reduced dendritic formations. Finally, the electrolyte was tested in practical pouch cell architecture, and the cells demonstrated excellent reliability even under mechanical stress. This work successfully reports a robust, rationally designed gelled electrolyte system for developing safe and high-performance quasi-solid state Li-S batteries.

A 3D network-structured gel polymer electrolyte with soluble starch for enhanced quasi-solid-state lithium-sulfur batteries

A Poly (vinylidene Fluoride-Hexafluoropropylene) Based Three-Dimensional Network Gel Polymer Electrolyte for Solid-State Lithium-Sulfur Batteries

An ultraviolet polymerized 3D gel polymer electrolyte based on multi-walled carbon nanotubes doped double polymer matrices for lithium-sulfur batteries

Novel Gel Polymer Electrolyte for High-Performance Lithium–sulfur Batteries

A Gel Polymer Electrolyte Based on PVDF-HFP Modified Double Polymer Matrices Via Ultraviolet Polymerization for Lithium-Sulfur Batteries

A newly designed composite gel polymer electrolyte based on poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP) for enhanced solid-state lithium-sulfur batteries.

In Situ Polymerization Bi‐Functional Gel Polymer Electrolyte for High Performance Quasi‐Solid‐State Lithium−Sulfur Batteries

Facile In Situ Chemical Cross-Linking Gel Polymer Electrolyte, which Confines the Shuttle Effect with High Ionic Conductivity and Li-Ion Transference Number for Quasi-Solid-State Lithium–Sulfur Battery

3D ultraviolet polymerized electrolyte based on PEO modified PVDF-HFP electrospun membrane for high-performance lithium-sulfur batteries

A quasi-solid polymer electrolyte initiated by two-dimensional functional nanosheets for stable lithium metal batteries

An in situ gel electrolyte for the facile preparation of high‐safety Li‐S battery

Porous Composite Gel Polymer Electrolyte with Interfacial Transport Pathways for Flexible Quasi Solid Lithium-Ion Batteries.

Supramolecular polymer cross-linking gel electrolyte for highly stable quasi-solid-state lithium metal batteries

A Three-Dimensional Co-Continuous Network Structure Polymer Electrolyte with Efficient Ion Transport Channels Enabling Ultralong-Life All Solid-State Lithium Metal Batteries

In-situ crosslinked single ion gel polymer electrolyte with superior performances for lithium metal batteries

Preparation and performances of the modified gel composite electrolyte for application of quasi-solid-state lithium sulfur battery

3D porous PTFE membrane filled with PEO-based electrolyte for all solid-state lithium–sulfur batteries

Dendrite-Free Solid-State Li Metal Batteries Enabled by Bifunctional Polymer Gel Electrolytes

Rationally Designed in-Situ Gelled Polymer-Ceramic Hybrid Electrolyte Enables Superior Performance and Stability in Quasi-Solid-State Lithium-Sulfur Batteries

Supramolecular Network Structured Gel Polymer Electrolyte with High Ionic Conductivity for Lithium Metal Batteries

Designing Polymer‐in‐Salt Electrolyte and Fully Infiltrated 3D Electrode for Integrated Solid‐State Lithium Batteries