Abstract:The material of Ti–6Al–4V has been widely applied in various industries, such as automobile, aerospace, and medical due to its high specific strength, superior thermal stability and strong corrosion resistance. In the recent decades, selective laser melting (SLM) has become an attractive method to fabricate Ti–6Al–4V parts, thanks to its significant advantages in low material consumption, the high degree of freedom in design, low carbon footprint, etc. Predictability of SLM material fatigue properties is especially important for the safety-critical structures under dynamic load cases. The present research is aimed at evaluating the low cycle fatigue (LCF) performance of SLM Ti–6Al–4V under high loading states. LCF tests were performed for as-built and annealed SLM Ti–6Al–4V. Comparison between LCF properties of SLM Ti–6Al–4V and the wrought Ti–6Al–4V was also made. It was found that as-built SLM Ti–6Al–4V demonstrated a comparable LCF performance with the wrought material. The LCF life of as-built SLM Ti–6Al–4V was longer than that of wrought Ti–6Al–4V at lower strain amplitudes. However, the wrought Ti–6Al–4V had better LCF performance at higher strain amplitudes. The results revealed that the porosity in the as-built SLM material exerted much more impact on the degradation of the material at high strain amplitudes. Annealing deteriorated the LCF performance of SLM Ti–6Al–4V material due to the formation of coarser grains. The cyclic Ramberg–Osgood and the Basquin–Coffin–Manson models were fitted to depict the cyclic stress–strain and the strain–life curves for the SLM Ti–6Al–4V, based on which the LCF performance parameters were determined. In addition, the fatigue fracture surfaces were observed by using scanning electron microscopy (SEM), and the results indicated that fatigue cracks originated from the surface or subsurface defects.

Cyclic plasticity of additively manufactured Ti-6Al-4V bracket for aeroengine application

High cycle fatigue performance evaluation of a laser powder bed fusion manufactured Ti-6Al-4V bracket for aero-engine applications

Fracture and Failure Behavior of Additive Manufactured Ti6Al4V Lattice Structures under Compressive Load

Hybrid Fabrication of Cold Metal Transfer Additive Manufacturing and Laser Metal Deposition for Ti6Al4V: The Microstructure and Dynamic/Static Mechanical Properties

A Novel Defect-Related Cyclic Damage Model Driven by Strain Energy Density for LPBF Titanium Alloy

Experimental and Crystal Plasticity Finite Element Investigations of Plastic Anisotropy in Additively Manufactured Ti6Al4V Alloy

Continuum damage mechanics-based fatigue life prediction of L-PBF Ti-6Al-4V

Tailoring microstructure with special bimodal structure to improve the ductility and fatigue life of laser powder bed fused Ti6Al4V alloy

Effects of Post-Processing and Loading Orientation on High-Cycle Fatigue of Selective Laser Melted Ti-6Al-4V

Very high cycle fatigue behavior of laser powder bed fusion additively manufactured Ti6Al4V alloy at elevated temperature

Crystal plasticity enhanced direct cyclic analysis of cyclic behaviour of LPBF-manufactured AISI 316L

Microstructural Features of Ti-6Al-4V Manufactured Via High Power Laser Directed Energy Deposition under Low-Cycle Fatigue

Evaluation of Low Cycle Fatigue Performance of Selective Laser Melted Titanium Alloy Ti–6Al–4V

Effect of Microstructure on Fatigue Properties of Several Ti-Alloys for Aerospace Application

The Low-Cycle Fatigue Behavior, Failure Mechanism and Prediction of SLM Ti-6Al-4V Alloy with Different Heat Treatment Methods

Anisotropic High Cycle Fatigue Property Estimation for Laser Additive Manufactured Ti6Al4V Alloy Dependence on Tomographic Imaging of Defect Population

Mechanical Properties and Failure Modes of Additively Manufactured Ti6Al4V Lattice Structures under Quasi-Static Compressive Loading

Effects of the Build Direction on Mechanical Performance of Laser Powder Bed Fusion Additively Manufactured Ti6Al4V under Different Loadings

Superior High-Cycle Fatigue Property Through In-Situ Precipitation of Α' Martensite in Additively Repaired Titanium Alloy

Multiple Α Sub-Variants and Anisotropic Mechanical Properties of an Additively-Manufactured Ti-6Al-4V Alloy

Mechanical Behavior Assessment of Ti-6Al-4V ELI Alloy Produced by Laser Powder Bed Fusion