Abstract:Heavy metal-based vehicle caused increase in fuel consumption, which creates pollution in the environment; thus, scientists across the nation researched to produce light weight, cost-effective, easy degradable, corrosive resistant composite material. Due to such features present in the composite material, the present research aims to examine the impact of alkali-silane treatment on the time-dependent and machining behavior of composites. Further, the alkali treatment and silane treatment on fiber and filler particle are carried out to provide even dispersion of filler particle and better reinforcement and interfacial bonding adhesion to the composite material, which makes a novelty to this study. The obtained fiber and filler particle were reinforced to matrix by using hand layup method and subsequently cured. This prepared composite material's strength is analyzed as per the ASTM standards. The results indicate that the inclusion of surface modified corn-fiber reinforced EF composite shows stronger interfacial adhesion, which implies loss factor of 42.8% lower than neat epoxy. Similarly, reinforcing corn husk fiber increases the energy release rate by 2500% and the fracture toughness by 156.47% when compared to pure epoxy composite. Further, the inclusion of biosilica particle of 2.0 vol.% exhibited the highest storage modulus of 5.69 GPa and the lowest loss factor of 0.32. This demonstrates the beneficial effect of combining alkali and silane treatment on corn fiber and filler particle. The epoxy composite (EFP3) of chemically treated fiber 30 vol.% and 2 vol.% of biosilica reinforcement exhibits a higher fatigue life cycle, fracture toughness, and energy release rate of 30,546, 26.5 MPa√m, and 0.86 MJ/m 2 , respectively. Similarly, the composite designation EFP3 has the lowest contact angle of 78°, indicating the preserved hydrophobicity. A drilling study has shown that using a 4-mm drill bit and 8-mm drill bit. The resultant of the drilling studies concludes that the use of 2.0 vol.% biosilica reduced the occurrence of fiber pull-out while drilling. Owing to such improved strength properties, light weight, corrosive resistant features in the biocomposite are applied in industries such as automotive, sporting goods, food and drug packaging, aerospace, and other technical applications that require strong load-bearing capacity, etc.

Damage investigations on natural fiber-epoxy human prosthetic composites toughened using echinoidea spike β-chitin biopolymer

Characterization of sea urchin spike chitin macromolecule and basalt-encapsulated bamboo fiber-epoxy environmental friendly composite for human prosthetic application

In vitro study of the biphasic calcium phosphate/chitosan hybrid biomaterial scaffold fabricated via solvent casting and evaporation technique for bone regeneration

Development of biocomposites using novel green pea pod lignin and hybridized pod sheath fibre-bamboo epoxy composite for human prosthetic application

Comparative Analysis of Erosive Wear Behaviour of Epoxy, Polyester and Vinyl Esters Based Thermosetting Polymer Composites for Human Prosthetic Applications Using Taguchi Design

Development and Structural Evaluation of Dog Bone Particle–Reinforced Epoxy Composites for Biomedical Applications

Comparative Study of the Mechanical and Water Absorption Behaviour of Basalt Fiber Reinforced Polymer Matrix Composites with Different Epoxies as Matrix for Biomedical Applications

Effect of silane-treated lignin and hybrid bamboo-green pea sheath fiber on mechanical, wear, and wettability behavior of epoxy structural composite

Physical and Mechanical Characterization of Bamboo Fiber/Groundnut Shell/Copper Particle/MWCNT-Filled Epoxy Hybrid Polymer Nanocomposites

Experimental investigation on bamboo fiber reinforced epoxy polymer composite materials developed through two different techniques

Experimental investigation on mechanical performance and drilling behavior of hybrid polymer composites through statistical and machine learning approach

Valorisation of corn waste as fiber, biosilica, and their epoxy composites: fatigue, fracture toughness, water absorption, and drilling properties

Experimental investigation of PCL‐based composite material fabricated using solvent‐cast 3D printing process

Evaluating the bioactivity of a hydroxyapatite-incorporated polyetheretherketone biocomposite

An in vitro wear behavior analysis of polymer composite for biomedical application

Reinforcing Hydroxyapatite/thermosetting Epoxy Composite with 3-D Carbon Fiber Fabric Through RTM Processing

Optimization and Prediction of Wear Characteristics of Khas Khas Grass/Mesquite Bark Powder/Banana Fiber-Reinforced Epoxy Green Hybrid Composites Using Taguchi Technique

Development of silane-treated corn husk fiber and agro-waste biofiller-reinforced epoxy composite: effects on wear, mechanical, thermal, and water absorption properties

Investigations on Low-Velocity Ballistic Impact behaviour of Kevlar / Epoxy Composites Reinforced with Chopped Wet Spun Fibers Intruded with Nanofillers

Characterizing tensile and flexural properties of synthetic fibers-reinforced epoxy composite for foot prosthetic application

Thermo‐mechanical performance of oil palm/bamboo fiber reinforced bio epoxy hybrid composites