Abstract:To alleviate the shortage of river sand (RS) and recycle abandoned resources, two recycled manufactured sands (RMSs) produced from tunnel excavation rock (tuff manufactured sand, TS) and granite cutting waste (granite manufactured sand, GS) are studied and compared with standard sand (SS) and RS. The aim is to identify the application potential of the two RMSs in cement-based materials. This is done by analyzing their influences on the mortar properties based on their surface characteristics and establishing a correlation between the surface characteristics of RMS and mortar properties. For the parent rock, petrographic analysis is performed and the uniaxial compressive strength is measured. For sand, the physical properties are evaluated and X-ray diffraction is used for analyzing the chemical composition. Digital image processing, nitrogen adsorption, and X-ray computed tomography are employed to determine the surface characteristics of sand particles. For the mortar, the fluidity, mechanical strength, water absorption, early total shrinkage, and accelerated expansion ratio are measured. The microstructure of the mortar interface transition zone is examined. Mercury intrusion porosimetry and thermogravimetric analysis are conducted to study the internal mechanism. The results indicate that compared with SS, the two RMSs reduce the fluidity of fresh mortar. In addition, TS is beneficial for the flexural, compressive, and tensile strengths of hardened mortar because of its denser internal pore structure and high degree of hydration caused by the properties of sand. The mechanical strength of the GS mortar can reach a similar or slightly higher level than that of the SS mortar. Furthermore, the fluidity and mechanical strength are well correlated with two parameters of sand, namely, roundness and specific surface area. The tensile strain capacity of the RMS-based mortar is superior to those of the SS and RS mortars. However, RMS increases the early total shrinkage. Although the TS mortar has the highest tensile strain capacity, it also has the largest early total shrinkage among the four mortar mixtures. Comparing the escalations in tensile strain capacity and early total shrinkage, the TS increases the risk of shrinkage cracking in the early stages. The effect of GS on the mortar tensile strain capacity is slightly greater than that on the early total shrinkage; thus, there is no significant influence on the risk of early shrinkage cracking in the GS mortar. In the accelerated expansion test, the TS shows potential alkali-silica reaction (ASR) risk in accordance with ASTM C1260, however, the GS indicates no potential for expansion damage. Based on the performance of various sands and mortars, GS has a better application value than TS. As for the TS mortar, it is necessary to consider the shrinkage cracking risk and ASR hazard in practical applications.

Physical and Mechanical Properties of Novel Gypsum-Based Self-Leveling Mortars: The Effect of Sand Gradation and Type

Application Potential of Granite Cutting Waste and Tunnel Excavation Rock As Fine Aggregates in Cement-Based Materials Based on Surface Characteristics

Effect of Mineral Admixtures on Physical, Mechanical, and Microstructural Properties of Flue Gas Desulfurization Gypsum-Based Self-Leveling Mortar

Effect of Additives on the Rheological and Mechanical Properties of Microfine-Cement-Based Grout

High value-added utilization of desulfurized building gypsum as self-leveling mortar: the comprehensive effect of cement

A Novel Gypsum-Based Self-Leveling Mortar Produced by Phosphorus Building Gypsum

Study of Early-Age Hydration, Mechanical Properties Development, and Microstructure Evolution of Manufactured Sand Concrete Mixed with Granite Stone Powder

Influence of the physical characteristics of sand and the crushed filler content on the properties of self-leveling mortars

Performance Characteristics of Micro Fiber-Reinforced Ambient Cured One-Part Geopolymer Mortar for Repairing

The Effect of Sand Type on the Rheological Properties of Self-Compacting Mortar

Optimization of mechanical properties and water absorption behavior of building gypsum by ternary matrix mixture

Mechanical properties and durability evaluation of self-compacting mortars containing glass and brick powders

Workability and Mechanical Properties of Superplasticized Microfine Cement Grouts

Effect of Paste Fluidity and Paste-to-Aggregate Ratio on the Strength and Permeability of Porous Mortar from Manufactured Sand

Mix Design Processing for Self Compacting Geopolymer Mortar

Effect of sand–precursor ratio on mechanical properties and durability of geopolymer mortar with manufactured sand

Effect of fly ash and gypsum on drying shrinkage and mechanical properties of one‐part alkali‐activated slag mortar

Optimization design and mechanical properties of multi-component ecological gelling materials

Utilization of original phosphogypsum as raw material for the preparation of self-leveling mortar

Study on the Effect of Three Types of Calcium Sulfate on the Early Hydration and Workability of Self-Compacting Repair Mortar

Comparative study on the mechanical properties of solidified silty-fine sand reinforced by permeable polymer and traditional grouting materials