Abstract:Due to the advantages of low cost, easy fabrication, mechanical flexibility, the research on organic solar cells has attracted a lot of attentions in the last decades. Among countless organic materials, the most successful ones are conjugated polymers, which were widely used in bulk heterojunction (BHJ) in conjugation with the fullerene [1]. In view of the fact the interpenetratedphase-separated p-n composites offer more chances for excitons to reach the p-n interfaces, BHJ greatly facilitates the dissociation of photogenerated excitons before decaying to ground state. During exciton dissociation process, the exciton delocalization at an ultra fast timescale has been observed recently, which has considerable effects on the charge generation and device performance. In this work, based on the recent studies [2–4], we established a theoretical model of polymer solar cells (PSCs) incorporating the exciton delocalization process. Through the model, we found the increase of delocalized excitons (compared to the total generated excitons) will significantly improve the short-circuit current, open-circuit voltage, fill factor and power conversion efficiency of PSCs. Particularly, the saturations of fill factor and open-circuit voltage are also observed, and the saturation points depend on the active layer thickness and recombination rate. For instance,the device model of 200nm thickness active layer has the saturated fill factor at 70% delocalization ratio, which is close to the conventional ratio of practical devices. The device configuration studied comprises a BHJ active layer sandwiched between a transparent anode and a metal cathode. Moreover, the active material is a mixture of OC 1 C 10 -PPV, as the donor, and PCBM, as the acceptor [5]. The generation rate of excitons is assumed to be homogeneous. The model proposed involves both the drift-diffusion model for photocarriers (Eq. (1)) and the diffusion and dissociation model for excitons (Eq. (2)). The governing equations are given as follows equation where q is elementary charge, n(p) is the electron (hole) density, and r G , r R are the parametersfor controlling exciton generation and bulk recombination, respectively. E is the internal E-field. µ and D are the mobility and diffusion coefficients. The exciton density is denoted by X diff and k diss is the exciton dissociation rate. The recombination R is taken to be a bimolecular form,with the rate given by Langevin [6], and η s is 0.25 for the singlet excitons. Using the physical parameters given by experiments [5], the nonlinear governing equation sets are solved self-consistently. The excitons are delocalized at an ultra fast timescale to form electron-hole pairs, which is much faster than the photo carrier relaxation time and exciton diffusion time. Consequently, the delocalization process was simulated by directly inserting the delocalization ratio η del into the equations.

Ultrafast electron transfer and decay dynamics in a small band gap bulk heterojunction material

The Role Of Exciton Delocalization In The Performance Of Bulk-Heterojunction Polymer Solar Cells

Ultra-Fast Excitation Dynamics in Low Bandgap Polymer Solar Cell

Bulk P-I-n Heterojunction Solar Cells Made from Hyperbranched Phthalocyanine Polymers

Small-bandgap polymer photovoltaic devices

Nanomorphology and Charge Generation in Bulk Heterojunctions Based on Low‐Bandgap Dithiophene Polymers with Different Bridging Atoms

A Tale of Current and Voltage: Interplay of Band Gap and Energy Levels of Conjugated Polymers in Bulk Heterojunction Solar Cells

Diketo-Pyrrolo-Pyrrole-Based Medium Band Gap Copolymers for Efficient Plastic Solar Cells: Morphology, Transport, and Composition-Dependent Photovoltaic Behavior

Excitation Dynamics in Low Band Gap Donor-Acceptor Copolymers and Blends

ChemInform Abstract: Review on the Recent Progress in Low Band Gap Conjugated Polymers for Bulk Hetero‐Junction Polymer Solar Cells

Impact of Nonfullerene Acceptor Core Structure on the Photophysics and Efficiency of Polymer Solar Cells

Insights into Excitonic Dynamics of Terpolymer-Based High-Efficiency Nonfullerene Polymer Solar Cells: Enhancing the Yield of Charge Separation States.

Two-dimensional Like Conjugated Copolymers for High Efficiency Bulk-Heterojunction Solar Cell Application: Band Gap and Energy Level Engineering

Excited-State Photophysics in A Low Band Gap Polymer with High Photovoltaic Efficiency

Charge Generation and Recombination in an Organic Solar Cell with Low Energetic Offsets

An Efficient, “Burn in” Free Organic Solar Cell Employing a Nonfullerene Electron Acceptor

Synthesis and Characterization of Thieno[3,2‐b]thiophene‐isoindigo‐based Copolymers As Electron Donor and Hole Transport Materials for Bulk‐heterojunction Polymer Solar Cells

Förster Resonance Energy Transfer and Improved Charge Mobility for High Performance and Low-Cost Ternary Polymer Solar Cells

Narrow Bandgap Donor–Acceptor Conjugated Polymer: Synthesis, Properties and Photovoltaic Application

High performance low band gap polymer solar cells with a non-conventional acceptor.

Efficient Hole Transfer from a Twisted Perylenediimide Acceptor to a Conjugated Polymer in Organic Bulk-Heterojunction Solar Cells