Abstract:Pollination is the key process in the hybrid rice seed production. To realizing mechanical pollination of hybrid rice, this paper designed and trial-manufactured a hybrid rice pollination machine combined collision and air-blowing method. Flow field distribution of two types of the pollination tube on the machine, including air-blow nozzle type and air-blow hole type were simulated using CFD technology. And the flow velocity out of each nozzle or hole on pollination tube was measured, and the pollination experiments in the paddy field using pollination machine prototype were carried out. In the experiment, the pollen distribution produced by mechanical pollination and manual pollination was measured adopting gravity slide method, and the flow field model of the pollen distribution was established using Gambit software and Fluent software. The k-ε standard turbulence model was adopted during the simulation of solving the control equations. The inlet boundary condition was set as velocity inlet, and the outlet boundary condition was set as pressure outlet, and the others were set as tube wall. The results of numerical simulation showed that under the same condition of the inlet velocity, the airflow outside of the pollination tube with air-blow hole type is slant, and there are some dead zones where air could not reach outside of the pollination tube. The airflow direction outside the pollination tube with air-blow nozzle type is almost the same, which can provide uniform and stable airflow field for pollination. So the pollination tube with air-blow nozzle type is the ideal structure for hybrid rice pollination machine. In order to verify the simulation results, a trial-produced pollination machine and two types of pollination tubes with air nozzles were built for experiments. The velocities out of the blower on the machine were measured by an anemograph under different engine gears. These velocities were also the inlet velocities of pollination tube and they were 5.40 m/s, 10.00 m/s and 13.50 m/s respectively. Then the velocity out of each air nozzle on pollination tube was measured by the same anemograph under the above three inlet velocities. The results showed that the variation trends of air velocity both by measured and simulated are the same. The average errors between simulation value and measured value are 2.14%, 2.40% and 3.43% respectively, and the uniformity variation coefficient of air flow distributing along the pollination tube is 14.76%, 15.93%, 16.31% respectively in simulation. The pollination experiments in paddy field were conducted by the trial-manufactured pollination machine when the outlet velocity was 7.30 m/s. The pollen was collected by glass slide coated with Vaseline and the acquisition points were set on the four lines of female parent against the male parent. The same experiment method was used to collect pollen during manual pollinating. The results of field pollination experiments showed that the pollen amount on each line and pollen distribution uniformity among lines in mechanization pollination are better than that of manual pollination when the outlet velocity of air-blow nozzle is 7.30 m/s. The pollination efficiency of the mechanical pollination is higher than that of manual pollination, which provides practical machine model for mechanization pollination of hybrid rice.

A Set of Artificial Pollination Technical Measures: Improved Seed Yields and Active Ingredients of Seeds in Oil Tree Peonies

Characterization of Agronomic and Seed Oil Features for Different Cultivars of Tree Peony

Annual Growth Cycle Observation, Hybridization And Forcing Culture For Improving The Ornamental Application Of Paeonia Lactiflora Pall. In The Low-Latitude Regions

Optimization of Ultrasound-Assisted Extraction of Peony Seed Oil with Response Surface Methodology and Analysis of Fatty Acid

Mining and expression analysis of candidate genes involved in regulating the chilling requirement fulfillment of Paeonia lactiflora ‘Hang Baishao’

Screening of Genes Related to Early and Late Flowering in Tree Peony Based on Bulked Segregant RNA Sequencing and Verification by Quantitative Real-Time PCR

Influences of Cross Pollination on Pollen Tube Growth and Fruit Set in Zuili Plums (prunus Salicina)

Callogenesis and Plant Regeneration in Peony (paeonia × Suffruticosa) Using Flower Petal Explants

Genomic basis of the giga-chromosomes and giga-genome of tree peony Paeonia ostii

Optimization of Airflow Velocity of Pneumatic Pollination for Hybrid Rice Breeding

Effects of Pollination by Honeybees on Oilseed Rape in Pinghu

Identification of genes associated with the biosynthesis of unsaturated fatty acid and oil accumulation in herbaceous peony ‘Hangshao’ (Paeonia lactiflora ‘Hangshao’) seeds based on transcriptome analysis

Optimization and Experiment on Pollination Tube of Collision and Air-Blowing Hybrid Rice Pollination Machine.

Optimizing the Working Performance of a Pollination Machine for Hybrid Rice

The Effect of Anti-browning Agent Activated Carbon and Polyvinyl Pyrrolidone on the Rooting of Embryo Seedlings of “FengDan” and Its Transcriptome Analysis

Optimization of an Aqueous Enzymatic Method and Supercritical Carbon Dioxide Extraction for Paeonia suffruticosa Andr. Seed Oil Production Using Response Surface Methodology (RSM)

Effects of Different Pollinating Varieties and Pollination Methods on Fruit Set and Quality of Cuiguan Pear under Plastic Culture

Full-Length Transcriptome and Transcriptome Sequencing Unveil Potential Mechanisms of Brassinosteroid-Induced Flowering Delay in Tree Peony

Transcriptome sequencing reveals terpene biosynthesis pathway genes accounting for volatile terpene of tree peony

Comparison on Pollen Fertility and Compatibility of Two ‘zuili'pium Varieties of Different Maturing Period

Non-Structural Carbohydrates Accumulation in Seedlings Improved Flowering Quality of Tree Peony under Forcing Culture Conditions, with Roots Playing a Crucial Role