Facile Preparation of a Carbon-Based Hybrid Film for Efficient Solar-Driven Interfacial Water Evaporation

Hanxue Sun,Yuanzhen Li,Jiyan Li,Zhaoqi Zhu,Wanting Zhang,Weidong Liang,Chonghua Ma,An Li

DOI: https://doi.org/10.1021/acsami.1c06226

2021-07-08

Abstract:Solar-driven interfacial water evaporation is one promising technology for seawater desalination and sewage purification because it offers a feasible and sustainable strategy to relieve global water scarcity. Herein, a novel hybrid film composed of recycled carbon soot and poly(vinyl alcohol) is developed by a very simple, green, and highly scalable "salt-assisted" assembling method. The hybrid film possesses characteristics with a porous structure, superhydrophilicity, ∼100% light absorption, and low thermal conductivity, which can effectively convert light into heat under solar illumination. Consequently, the hybrid film can achieve a photothermal conversion efficiency of 91.5% under a stimulated solar irradiation of 1 kW m^–2. Furthermore, the hybrid film can be applied for seawater desalination and dye wastewater purification. The findings of our work not only provide a new photothermal platform with high light-to-thermal conversion ability and good reusability but also open a new avenue for the applications of carbon soot-based hybrid films in solar-assisted water evaporation and sewage purification.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.1c06226?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.1c06226</a>.Snapshot of the SP-2 film on the irregular substrate; comparative pictures of the PVA/soot mixture with and without NaCl contact; shrinkage of the PVA and PVA/soot mixture on the NaCl tablet; snapshot of the SP-2 film after immersing in water for 6 months; effect of the mass ratio of soot and PVA and PVA concentration; final surface temperature of SP films; comparison of water harvesting performance of the SP films purifier under 1 sun illumination; snapshot and SEM images of the SP-2 film after solar illumination for 10 cycles; mass change in the SP-2 film; elemental analysis result of samples; and comparison of photothermal conversion ability between the SP-2 film and other films or membranes (<a class="ext-link" href="/doi/suppl/10.1021/acsami.1c06226/suppl_file/am1c06226_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

materials science, multidisciplinary,nanoscience & nanotechnology

What problem does this paper attempt to address?

The problem that this paper attempts to solve is to develop an efficient, low - cost and environmentally - friendly solar - driven interfacial water evaporation technology for seawater desalination and sewage treatment. Specifically, the researchers developed a hybrid film (SP film) based on recycled carbon soot and polyvinyl alcohol (PVA), which was prepared by a simple "salt - assisted" assembly method, aiming to achieve efficient photothermal conversion and good reusability.

### Specific background of the problem

1. **Global water shortage**: Although about 70% of the Earth's surface is covered by water, only 2.5% of the available freshwater resources are available, most of which are glaciers or deeply buried underground and difficult to extract. Therefore, ensuring an adequate supply of freshwater has become an important challenge for sustainable economic development.

2. **Limitations of traditional water treatment technologies**: Traditional water treatment technologies such as nanofiltration and reverse osmosis are effective, but they are costly, energy - intensive and have a large impact on the environment. In contrast, solar - driven interfacial water evaporation technology has the advantages of low cost, low energy consumption and environmental friendliness, and has become a viable alternative.

3. **Deficiencies of existing photothermal materials**: Existing photothermal materials have deficiencies in light absorption rate, heat management, water transport and stability, which limit their efficiency and reliability in practical applications.

### Research objectives

1. **Develop new photothermal materials**: Improve the efficiency of solar - driven interfacial water evaporation by designing and preparing carbon - soot - based hybrid films with high - efficiency photothermal conversion capabilities.

2. **Optimize the preparation process**: Use a green, simple and large - scale - producible "salt - assisted" assembly method to prepare photothermal films with porous structures and superhydrophilicity.

3. **Verify application potential**: Evaluate the performance of the prepared SP films in seawater desalination and dye wastewater treatment, and demonstrate their potential in practical applications.

### Main achievements

- **Efficient photothermal conversion**: The SP film exhibits a photothermal conversion efficiency of 91.5% under simulated solar illumination (1 kW m\(^{-2}\)).
- **Excellent physical properties**: The SP film has rapid water absorption, good flexibility and mechanical strength, and can work stably in complex environments.
- **Broad application prospects**: The experimental results show that the SP film is not only suitable for seawater desalination, but also can effectively purify dye wastewater, demonstrating its broad application potential in the field of environmental governance.

Through this research, the authors not only provided a new type of carbon - soot - based photothermal material, but also provided new ideas for using waste carbon soot resources to develop high - efficiency solar absorbers.