Abstract:Objectives: Three-dimensional (3D) printing technology has shown potential advantages in accurate and efficient tibial plateau fracture (TPF) treatment. This technology can provide structural morphology to repair fracture fragments. Here, we summarize our experience with the use of 3D printing technology during intraarticular osteotomy in the treatment of the malunion of TPF. Methods: The patients who were treated with malunion of TPF in our hospital between January 2015 and December 2018 were retrospectively analyzed. These patients were divided into two groups: the conventional group without 3D-printed model application and the 3D printing group with 3D-printed model application. All patients received the intraarticular osteotomy during operation, and we compared the operation time (min), fracture healing time (months), postoperative knee Rasmussen scores (0-30 points), knee mobility range (0-140°) (the independent t-test), fracture reduction evaluation (Biggi's method) (the chi-square test: Fisher's exact test), and postoperative complications of each group. Results: Twenty-six patients aged 18-65 years who underwent TPF revision operation were included in this study, including 18 patients in the conventional group, and eight patients in the 3D printing group. The follow-up time was 24-48 months, and the operation time was 185 min in the conventional group and 180 min in the 3D printing group. All patients received a bone union at the last follow-up. The healing time was 4.2 months in the conventional group and 3.75 months in the 3D printing group (p > 0.05). The respective postoperative Rasmussen scores were 24.6 and 26.2, and postoperative knee mobility was 103.5° and 118.5° in the conventional group and 3D printing group, respectively. Both the Rasmussen scores and degrees of mobility were significantly improved after surgery (p < 0.05), and the postoperative knee mobility was significantly better in the 3D printing group versus the conventional group (p < 0.05). Four patients still had a 2-mm collapse on the articular surface, and two patients still had slight valgus (<5°) in the conventional group. Only one case in the 3D printing group suffered from an articular surface collapse. Superficial wound infections occurred in two patients in the conventional group. Conclusion: The results show that 3D printing technology is an effective preoperative preparation in the treatment of TPF malunion. This technology can facilitate accurate preoperative planning to select the optimal surgical approach, plan the implant placement, visualize the screw trajectory, and anticipate possible intraoperative difficulties.

3D printing-assisted percutaneous fixation makes the surgery for scaphoid nonunion more accurate and less invasive

3-Dimensional Printing–Assisted Percutaneous Fixation for Acute Scaphoid Fracture: 1-Shot Procedure

Experimental Study and Preliminary Clinical Application of Mini-invasive Percutaneous Internal Screw Fixation for Scaphoid Fracture under the Guidance of a 3D-Printed Guide Plate

Three-dimensional-printed patient-specific Kirschner-wire guide for percutaneous fixation of undisplaced scaphoid fractures: a cadaveric study

Treatment of pseudoarticular scaphoid nonunion with bone graft and percutaneous fixation under wrist arthroscopy

Percutaneous Neutralization Screw with Arthroscopic Bone Grafting for Scaphoid Nonunion

3D printed guide-assisted percutaneous screw fixation for minimally displaced scaphoid waist fractures with delayed diagnosis or presentation

Titanium patient-specific scaphoid replacement for unreconstructable nonunions: a case series study

Treatment of Scaphoid Non-Unions with Custom-Made 3D-Printed Titanium Partial and Total Scaphoid Prostheses and Scaphoid Interosseous Ligament Reconstruction

Arthroscopic realignment and osteosynthesis of unstable scaphoid nonunion with cancellous bone graft from the ipsilateral radius

Comparative analysis of scaphoid nonunion treatment with screw fixation and angular stable plate

[Arthroscopic reconstruction of scaphoid nonunions]

Arthroscope Assisted Minimally Invasive Management of Scaphoid Fractures with Missed Diagnosis and Delayed Treatment

Arthroscopic Versus Open Bone Grafting and Internal Fixation of Scaphoid Nonunion—A Systematic Review

[Treatment for non-union scaphoid fractures with headless cannulated screws and distal radius cancellous autograft]

Subchondral Radial and Ulnar K-Wire Positioning With Cancellous Bone Graft Shortens Union Time in Scaphoid Waist Nonunion

The Efficacy of 3D Printing Model in the Intraarticular Osteotomy in the Treatment of Malunion of Tibial Plateau Fracture

Percutaneous fixation of scaphoid fractures:outcomes of 114 cases

Round table discussion. The management of proximal scaphoid nonunion

Clinical research on percutaneous cannulated compression screw fixation of scaphoid fracture via a dorsal approach

Three-dimensional Printing Technique Aids Screw Insertion into the Sustentaculum Tali of the Internal Fixation of Intra-Articular Calcaneal Fractures