Abstract:Radiation detectors have two main detection mechanisms: direct conversion, which utilises a photoconductor to directly convert radiation into an electrical signal, and indirect conversion, which utilises a scintillator to convert radiation into visible light, which is subsequently converted into an electrical signal. The photoconductor material, mercury (II) iodide (HgI 2 ) sensitive to visible light, has the property of gradually decreasing signal for repeated irradiation beams. Therefore, this study aimed to improve the signal magnitude and stability to repeated measurements of polycrystalline HgI 2 by mixing 0, 4, 6, 8, 10, and 20 weight percent (wt%) of terbium-doped gadolinium oxysulfide (GOS:Tb), a scintillator material that emits visible light. The performance of these dosimeters was evaluated with a focus on dosimetric parameters such as signal quantity, short-term repeatability, dose-response linearity, and dose-rate dependence to assess their potential application in radiotherapy quality assurance (QA). The results from the dosimeters were compared with those from a metal-oxide-semiconductor field-effect transistor (MOSFET) dosimeter and an ionisation chamber. Peak was found for the dosimeter with 8 wt% GOS:Tb but decreased for the dosimeters with 10 and 20 wt% GOS:Tb. The standard deviations of short-term repeatability were 1.45%, 0.86%, 1.18%, 1.51%, 131%, and 4.48% for dosimeters with 0, 4, 6, 8, 10, and 20 wt% GOS:Tb, respectively. The dosimeters with 4 and 6 wt% GOS:Tb had better standard deviations of repeatability than the MOSFET (1.35%), but not better than the ionization chamber (0.5%). All dosimeters, the MOSFET, and the ion chamber demonstrated excellent dose-response linearity for monitor unit (MU) values ranging from 2 to 500, with R 2 values exceeding 0.9997. The sensitivity analysed using the linear slope was the highest for the dosimeter with 6 wt% GOS:Tb (0.103) and the MOSFET (0.0103) among all dosimeters. The dosimeter with 6 wt% GOS:Tb and the MOSFET exhibited deviations of 4.64% and 3.31%, respectively, at a dose rate of 100 cGy/min, thus failing to meet the evaluation standard of within 2%. The ion chamber, however, achieved compliance with a deviation of 0.15%. Therefore, it is necessary to apply correction factors to each dose rate when using hybrid dosimeters for QA. The optimal mixing ratio of GOS:Tb for manufacturing the hybrid dosimeter was determined to be 6 wt%, suggesting signal amplification through visible light and a potential improvement in operational stability through pore filling of the material.

Optical investigation of MAGAT polymer gel dosimeter embedded with methylene blue dye and zinc oxide nanoparticles using UV/Vis spectrometry pre- and post-irradiation of 6MV photon beam

Ultrasound evaluation of polymathic methacrylate (PMMA) gel dosimeter doped with copper oxide (CuO) nanoparticles

Magnetic Resonance Imaging Stud of New PAGAT Polymer Gel Dosimeter

Basic Properties of a New Polymer Gel for 3D-Dosimetry at High Dose-Rates Typical for FFF Irradiation Based on Dithiothreitol and Methacrylic Acid (MAGADIT): Sensitivity, Range, Reproducibility, Accuracy, Dose Rate Effect and Impact of Oxygen Scavenger

The investigation of dose rate and photon beam energy dependence of optimized PASSAG polymer gel dosimeter using magnetic resonance imaging

Optical characterization of Fricke-methylthymol blue hydrogel dosimeter with gellan gum as physical cross-linker

A basic study of some normoxic polymer gel dosimeters

Comparison Of Alpha and X-ray Irradiation Effects in nMAG Polymer Gels Used for Dosimetry Applications

Direct Response to Proton Beam Linear Energy Transfer (let) in A Novel Polymer Gel Dosimeter Formulation

Preliminary Research on the Dose Response of Polymer Gel Dosimeter with Carbon Beam Irradiation

Characterization of the chemical and structural modifications induced by X rays on the HEMA based polymer gel

Toward “on-line” X-ray computed tomography-based dosimetry using a new polymer gel with rapid response

Preliminary Study of Normoxic PAGAT Polymer Gel Dosimeter by Adding Formaldehyde

Evaluation of photoconductor and scintillator hybrid dosimeters for radiation therapy quality assurance

Synthesis and Characterization of a New Nanocomposite Film Based on Polyvinyl Alcohol Polymer and Nitro Blue Tetrazolium Dye as a Low Radiation Dosimeter in Medical Diagnostics Application

X-rays sensing properties of MEH-PPV, Alq₃ and additive components: a new organic dosimeter as a candidate for minimizing the risk of accidents of patients undergoing radiation oncology

Advancements and applications of dosimetry techniques in modern medical radiation therapy: a comprehensive review

Feasibility of new polymeric matrices in the production of ferrous sulphate dosimeters

End-to-End QA with Polymer Gel Dosimeter for Photon Beam Radiation Therapy

Experimental evaluation of electrospun ZnO/WO 3 /PVA-coated glass nanocomposites for a potential radiation dosimetry application

Investigation of silver nanoparticles embedded in extracted gelatins from camel, bovine, and fish bones for possible use in radiation dosimetry