Abstract:Comparative evaluation of solid particle erosion resistance in milled carbon fiber reinforced basalt fiber epoxy composites; effect of abrasive shape variations on the damage mechanism. The solid particle erosive wear performance of basalt fiber‐reinforced epoxy composites with the incorporation of different percentages of milled carbon fiber fillers (0–10 wt%) is evaluated under various abrasive materials (garnet and ceramic beads) and impingement angles (30° and 90°). Erosion tests have been carried out following ASTM G76 standards using a factorial design method. The data indicate that the erosion rates, crater depths, and areas of craters are all strongly dependent on erodent material type and milled carbon fiber filler ratio. Compared to ceramic beads, garnet abrasives caused severe erosion, with erosion rates reaching approximately 500 mg/g at a 90° impingement angle without milled carbon fiber fillers. Erosion by both abrasives was significantly reduced by the introduction of milled carbon fiber fillers into the basalt fiber composites, with the erosion rate decreasing to around 100 mg/g with 3 wt% milled carbon fiber fillers. The maximum crater depth was also influenced; garnet abrasives produced craters as deep as 1000 μm without fillers at 90°, which was reduced to 451 μm with 3 wt% milled carbon fiber fillers when ceramic beads were used. Of the three factors for the erosion rate and crater depth, inorganic erodent material and ratio of carbon fiber filler were prominent, but the impingement angle effect was much smaller. Among the three factors for the erosion rate and crater depth, erodent material and carbon fiber filler ratio were prominent, while the impingement angle effect was significantly less. Highlights The garnet abrasives cause more severe erosion than ceramic beads at 90°. Composites exhibit optimal erosion resistance with 3–5 wt% milled carbon fiber fillers. Filler ratio and erodent material type significantly impact erosion rates and depths. Factors affecting wear performance identified using factorial design and ANOVA.

Solid particle erosion wear characteristics of fiber and particulate filled polymer composites: A review

Artificial Neural Network and Response Surface Methodology Based Analysis on Solid Particle Erosion Behavior of Polymer Matrix Composites

Erosive Wear Resistance of Fiber-reinforced Epoxy Resin to Solid Particle Flow

Study on the erosion wear characteristics and mechanisms of UBHMWPE/kaolin composites

Influence of Some Key Parameters on Erosion Rate for Composite Materials

Erosion analysis of fiber reinforced epoxy composites

Abrasive wear behaviour of orange peel (biowaste) particulate reinforced polymer composites

Comparative Analysis of Erosive Wear Behaviour of Epoxy, Polyester and Vinyl Esters Based Thermosetting Polymer Composites for Human Prosthetic Applications Using Taguchi Design

A review on mechanical and wear properties of fiber-reinforced thermoset composites with ceramic and lubricating fillers

Erosion wear analysis of coconut shell dust filled epoxy composites using computational fluid dynamics and Taguchi method

Recent Progress in the Development and Evaluation of Rain and Solid Particle Erosion Resistant Coatings for Leading Edge Protection of Wind Turbine Blades

Parametric Analysis for Erosion Wear of Waste Marble Dust-Filled Polyester Using Response Surface Method and Neural Networks

Fundamental aspects and recent progress on wear/scratch damage in polymer nanocomposites

Surface topography modification, Film transfer and Wear mechanism for fibre reinforced polymer composites—An Overview

Air Jet Erosion Wear Behavior of Al6061-SiC-Carbon Fibre Hybrid Composite

Influence of fillers and fibre reinforcement on abrasive wear resistance of some polymeric composites

Abrasive wear of graphite fiber-reinforced polymer composite materials

Comparative evaluation of solid particle erosion resistance in milled carbon fiber‐reinforced basalt fiber epoxy composites: Impact of abrasive shape variations

Development and erosion wear analysis of polypropylene/Linz‐Donawitz sludge composites

Wear and Frictional Performance of Epoxy Composites Reinforced with Natural Waste Fibers and Fillers for Engineering Applications

Influence of Load and Sliding Velocity on Abrasive Wear of Polyester Composites Reinforced with Bio-Particulates as Filler Material