Abstract:In this paper, Cu thin films were deposited on Si (100) substrates by the high-power impulse magnetron sputtering (HiIPMS) technique, and the effects of different duty cycles (from 2.25% to 5.25%) on the plasma discharge characteristics, microstructure, and electrical properties of Cu thin films were investigated. The results of the target current test show that the peak target current remains stable under 2.25% and 3% duty cycle conditions. Under the conditions of a 4.5% and 5.25% duty cycle, the target peak current shows a decreasing trend. The average power of the target shows a rising trend with the increase in the duty cycle, while the peak power of the target shows a decreasing trend with the increase in the duty cycle. The results of OES show that with the increase in the duty cycle, the total peak intensity of copper and argon emissions shows an overall increasing trend. The duty cycle from 3% to 4.5% change in copper and argon emission peak total intensity change is not obvious. The deposition rate and surface morphology of the copper film were investigated by scanning electron microscopy, and the deposition rate of the copper film increased with the increase in the duty cycle, which was mainly due to the increase in the average power. The surface roughness of the copper film was evaluated by atomic force microscopy. X-ray diffraction (XRD) was used to analyze the grain size and texture of the Cu film, and the results showed that the average grain size of the Cu film increased from 38 nm to 59 nm on the (111) and (200) crystal planes. Four-probe square resistance test copper film resistivity in 2.25%, 3% low duty cycle conditions of the copper film resistivity is generally higher than 4.5%, 5.25% high duty cycle conditions, the copper film resistivity shows the trend of change is mainly affected by the copper film grain size and the (111) face of the double effect of the optimal orientation. The lowest resistivity of the copper film measured under the 4.5% duty cycle condition is 1.7005 μΩ·cm, which is close to the intrinsic resistivity of the copper film of 1.67 μΩ·cm.

Effect of duty cycle on microstructure and mechanical properties of AlCrN coatings deposited by HiPIMS

Effects of duty cycle on microstructure and mechanical properties of (AlCrNbSiTi)N high-entropy nitride hard coatings deposited by pulsed arc ion plating

Effects of duty cycle on microstructure of TiN coatings prepared using CAE/HiPIMS

The effect of duty cycle on the mechanical and electrochemical corrosion properties of multilayer CrN/CrAlN coatings produced by cathodic arc evaporation

Effects of Input Power Ratio of AlCr/Ti Target on the Microstructural and Mechanical Properties of AlTiCrN Coatings Synthesized by a High-Power Impulse Magnetron Sputtering Process

Effects of Carbon Doping and DC Bias Voltage on Microstructure and Mechanical Properties of AlCrCN Films Synthesized via HiPIMS

On the Effect of Aluminum on the Microstructure and Mechanical Properties of CrN Coatings deposited by HiPIMS

Mechanical properties of amorphous and crystalline CrN/CrAlSiN multilayer coating fabricated using HPPMS

Structure, mechanical and tribological properties of thick CrNx coatings deposited by HiPIMS

Effect of bias voltages and interlayer design on microstructure, mechanical properties, and adhesion performance of AlCrSiN coatings deposited using HiPIMS

Effects of Substrate Rotation Speed on Structure and Adhesion Properties of CrN/CrAlSiN Multilayer Coatings Prepared Using High-Power Impulse Magnetron Sputtering

Effects of HiPIMS Duty Cycle on Plasma Discharge and the Properties of Cu Film

Effect of the pulse frequency on the structure, mechanical and tribological properties of Ti-Al-Ta-N coatings deposited by HiPIMS

Comparison of CrN Coatings Prepared Using High-Power Impulse Magnetron Sputtering and Direct Current Magnetron Sputtering

Design of cycle structure on microstructure, mechanical properties and tribology behavior of AlCrN/AlCrSiN coatings

Effect of peak current on the microstructure, mechanical properties and tribological behavior of Mo x N coatings deposited by high power impulse magnetron sputtering

Effect of Si contents on microstructure and mechanical characteristics of TiAlSiN thin film deposited by HiPIMS using different Ti Si target compositions

Effect of C doping on structure and properties of TiAlCrN coatings by filter cathode vacuum arc deposition

Structure and Properties of Arc Ion Plating Deposited AlCrSiN Coatings Controlled by Pulsed Bias Voltage

Microstructures and Mechanical Properties of CrN Coatings Deposited by HIPIMS

Effects of modulation ratio on microstructure and properties of TiN/TiAlN multilayer coatings