Abstract:Background: Contrast-enhanced spectral mammography (CESM) with photon-counting x-ray detectors (PCDs) can be used to improve the classification of breast cancers as benign or malignant. Commercially-available PCD-based mammography systems use silicon-based PCDs. Cadmium-telluride (CdTe) PCDs may provide a practical advantage over silicon-based PCDs because they can be implemented as large-area detectors that are more easily adaptable to existing mammography systems. Purpose: The purpose of this work is to optimize CESM implemented with CdTe PCDs and to investigate the influence of the number of energy bins, electronic noise level, pixel size, and anode material on image quality. Methods: We developed a Monte Carlo model of the energy-bin-dependent modulation transfer functions (MTFs) and noise power spectra, including spatioenergetic noise correlations. We validated model predictions using a CdTe PCD with analog charge summing for charge-sharing suppression. Using the ideal-observer detectability, we optimized CESM for the task of detecting a 7-mm-diameter iodine nodule embedded in a breast with 50% glandularity. We optimized the tube voltage, beam filtration, and the location of energy thresholds for 50 and 100- μ $\mu$ m pixels, tungsten and molybdenum anodes, and two electronic noise levels. One of the electronic noise levels was that of the experimental system; the other was half that of the experimental system. Optimization was performed for CdTe PCDs with two or three energy bins. We also estimated the impact of anatomic noise due to background parenchymal enhancement and computed the minimum detectable iodine area density in the presence of quantum and anatomic noise. Results: Model predictions of the MTFs and noise power spectra agreed well with experiment. For optimized systems, adding a third energy bin increased quantum noise levels and reduced detectability by ∼55% compared to two-bin approaches that simply suppress contrast between fibroglandular and adipose tissue. Decreasing the electronic noise standard deviation from 3.4 to 1.7 keV increased iodine detectability by ∼5% and ∼30% for two-bin imaging and three-bin imaging, respectively. After optimizing for tube voltage, beam filtration, and the location of energy thresholds, there was ∼a 3% difference in iodine detectability between molybdenum and tungsten anodes for two-bin imaging, but for three-bin imaging, molybdenum anodes provided up to 14% increase in detectability relative to tungsten anodes. Anatomic noise decreased iodine detectability by 15% to 40%, with greater impact for lower electronic noise settings and larger pixel sizes. Conclusions: For CESM implemented with CdTe PCDs, (1) quantitatively-accurate three-material decompositions using three energy bins are associated with substantial increases in quantum noise relative to two-energy-bin approaches that simply suppress contrast between fibroglandular and adipose tissues; (2) tungsten and molybdenum anodes can provide nearly equal iodine detectability for two-bin imaging, but molybdenum provides a modest detectability advantage for three-bin imaging provided that all other technique parameters are optimized; (3) reducing pixel sizes from 100 to 50 μ $\mu$ m can reduce detectability by up to 20% due to charge sharing; (4) anatomic noise due to background parenchymal enhancement is estimated to have a substantial impact on lesion visibility, reducing detectability by approximately 30%.

Improving CdMnTe Detector Performance by Adding 2% of Selenium

Role of selenium addition to CdZnTe matrix for room-temperature radiation detector applications

Impact of selenium addition to the cadmium-zinc-telluride matrix for producing high energy resolution X-and gamma-ray detectors

High-Performance 1D CdS/2D Te Heterojunction Photodetector

Characterization of high Zn content Cd0.87Zn0.13Te0.98Se0.02 grown using Bridgman technique

The Design of Mn2+&Co2+ Co-Doped CdTe Quantum Dot Sensitized Solar Cells with Much Higher Efficiency.

Bridgman-grown (Cd,Mn)Te and (Cd,Mn)(Te,Se): A comparison of suitability for X and gamma detectors

A New Strategy to Improve the Performance of MoS2-based 2D Photodetector by Synergism of Colloidal CuInS2 Quantum Dots and Surface Plasma Resonance of Noble Metal Nanoparticles

Monte-Carlo study of contrast-enhanced spectral mammography with cadmium telluride photon-counting x-ray detectors

Recent Progress in CdTe and CdZnTe Detectors

Growth and characterization of large-size CdMgTe single crystals doped with different in amounts

CdTe X/γ-ray Detectors with Different Contact Materials

Imaging and Spectral Performance of a 60 μm Pitch CdTe Double-Sided Strip Detector

Band Gap Variation of CdInSe and CdZnS Fabricated by High Throughput Combinatorial Growth Technique

Progress in the Development of CdZnTe Unipolar Detectors for Different Anode Geometries and Data Corrections

Optimization of an ultra-high-resolution parallel-hole collimator for CdTe semiconductor SPECT system

Improving the Performance of Solution-Based CZTSSe Absorber by Selenization Annealing with Selenium Powder in Argon

CdTe Based Energy Resolving, X-ray Photon Counting Detector Performance Assessment: The Effects of Charge Sharing Correction Algorithm Choice

Growth modulation of nonlayered 2D-MnTe and MnTe/WS2 heterojunction for high-performance photodetector

In-Synthesis Se-Stabilization Enables Defect and Doping Engineering of HgTe Colloidal Quantum Dots