Abstract:Lithium titanate is one of the most promising candidates among advanced tritium breeders for fusion reactors. However, the tritium breeding ratio (TBR) of Li 2 TiO 3 is smaller than that of Li 2 O or Li 8 TiO 6, etc., due to its lower Li density. Therefore, new Li-containing ceramics with both high stability and high Li density need to be further explored. In this work, the Li 2+ x TiO 3 powder with high Li content was prepared by the sol-gel method, and the pebbles were fabricated by a wet forming process. The effect of excess lithium on the crystal structure and performance of Li 2+ x TiO 3 were systematically investigated. The synthesis temperature of Li 2+ x TiO 3 powder with a well-developed crystal structure prepared by this method was 500 °C, and all the diffraction patterns of sintered Li 2+ x TiO 3 ( x = 0–0.4) powder were the same as those of β-Li 2 TiO 3 phase and no second phase peaks are observed. These results demonstrated that Li 2+ x TiO 3 powder was a solid solution with high Li content. The particle size distribution of Li 2+ x TiO 3 powder was about 40–90 nm. As x = 0.3, the Li content is stable both in Li 2+ x TiO 3 powder and pebbles, and the Li 2.3 TiO 3 pebbles presented a very high relative density of 87%, a small grain size of 1.8 μm, and good sphericity of 0.98, respectively. Especially, the crushing load reached 50 N. Thus, the Li 2.3 TiO 3 solid solution pebble is an important candidate breeder material for advanced tritium breeders.Kindly check and confirm street information is correctly identified for Affiliation 1.The street information is correctly identified for Affiliation 1.We are very grateful for your additions.

Preparation of Li 4 SiO 4 pebbles with high strength and inhibited lithium volatilization via lithium alginate

Preparation of Li4SiO4 pebbles with increased lithium content and crush load via molten salt assisted sintering

Fabrication of Li2TiO3 Pebbles by Water-Based Sol–gel Method

Additive manufacturing of high-quality tritium breeding pebbles using ceramic precursors

Microfabrication of Li 4 SiO 4 pebbles with complex pore structure via digital light processing: Accuracy control and properties optimizing

Efficient fabrication of high strength Li2TiO3 ceramic pebbles via improved rolling ball method assisted by sesbania gum binder

Characterization of Li-rich Li2TiO3 ceramic pebbles prepared by rolling method sintered in air and vacuum

Effects of High Li Content on the Crystal Structure and Properties of Li2+xTiO3 Ceramic Pebbles by Sol-Gel Method

Preparation of tritium breeding Li 2 TiO 3 ceramic pebbles via newly developed piezoelectric micro‐droplet jetting

Tritium Release Performance of Biphasic Li2TiO3-Li4SiO4 Ceramic Pebbles Fabricated by Centrifugal Granulation Method

Preparation of Li4TiO4-Li2TiO3 core-shell ceramic pebbles with thick shells and high strength through an improved granulation method

Grain growth mechanism and thermal stability of Li2TiO3 pebbles fabricated by wet method

Low-temperature synthesis of Li2TiO3 tritium breeder ceramic pebbles by water controlled-release solvothermal process

Lithium/titanium ratio: A key factor on crystal structure and mechanical properties of lithium titanate pebbles for tritium breeder

A novel process for fully automatic mass-production of Li2TiO3 ceramic pebbles with uniform structure and size

A comprehensive study on Li4Si1−xTixO4 ceramics for advanced tritium breeders

Fabrication of high strength Li-rich 2Li2TiO3–Li4SiO4 composite breeding ceramics at low-temperature by two-step sintering

Fabrication of fine-grained Li2TiO3 ceramic pebbles with enhanced crush load by rolling method: Optimization of Li/Ti ratio and sintering procedure

Alkaline hydrothermal treatment of P25 titanium dioxide for low temperature sintering of Li 2 TiO 3 tritium breeding ceramics

Fabrication of fine‐grained Li2TiO3 ceramic with enhanced performance using high‐energy ball milling

Design, synthesis and characterization of advanced tritium breeder: Li4Si1-xTixO4 ceramics