Abstract:This study presents a novel combined generative shaping and material-forming (GSM) approach for preparing tritium breeder units for fusion reactors using 3D printing technology. For the first time, defect-free lithium-rich Li4SiO4 porous structures were successfully prepared by combining photopolymerization and reaction sintering processes based on the use of low-cost Li2CO3 and SiO2 ceramic powders. Investigation was conducted on the preparation of the ceramic powder-based mixture slurry as well as the photopolymerization 3D printing and reaction sintering processes. Li4SiO4-based porous lattice ceramics with high purity, no obvious defects, and adjustable packing fraction were fabricated. The mechanical properties of the samples prepared with different packing fractions were then evaluated. The prepared samples showed better mechanical properties than the pebble bed structures with similar packing fractions. At a packing fraction of 92.10%, the crushing strength and elastic modulus reached 186.49±0.04 MPa and 16.47±0.03 GPa, respectively. These results show that the combination of photopolymerization 3D printing and reaction sintering processes based on the use of low-cost ceramic powders has significant advantages in terms of flexibility and efficiency in structure design and fabrication and cost-effectiveness in material forming with enhanced performance, providing a promising route to produce high-performance tritium breeder structures for fusion technologies. In particular, the present combined method also paves a promising generalized way to enable effective generative structure-shaping and material-forming in the advanced ceramic manufacturing industry, not to mention that the preparation of high-performance Li4SiO4 tritium breeder units for fusion technologies.

Microfabrication of Li 4 SiO 4 pebbles with complex pore structure via digital light processing: Accuracy control and properties optimizing

Fabrication and characteristics of Li4SiO4 pebbles by a novel capillary-based microfluidic wet process

Fabrication of Li2TiO3 Pebbles by Water-Based Sol–gel Method

Additive manufacturing of high-quality tritium breeding pebbles using ceramic precursors

Fabrication of the Li2tio3 Tritium Breeder Pebbles by A Capillary-Based Microfluidic Wet Process

Preparation of tritium breeding Li 2 TiO 3 ceramic pebbles via newly developed piezoelectric micro‐droplet jetting

Preparation of Li 4 SiO 4 pebbles with high strength and inhibited lithium volatilization via lithium alginate

A novel process for fully automatic mass-production of Li2TiO3 ceramic pebbles with uniform structure and size

Preparation of Li4SiO4 pebbles with increased lithium content and crush load via molten salt assisted sintering

Efficient fabrication of high strength Li2TiO3 ceramic pebbles via improved rolling ball method assisted by sesbania gum binder

Photopolymerization and reaction sintering enabled generative shaping and material-forming of complex ceramic structures with high performance

Characterization of Li-rich Li2TiO3 ceramic pebbles prepared by rolling method sintered in air and vacuum

3D printing of ceramic cellular structures for potential nuclear fusion application

Grain growth mechanism and thermal stability of Li2TiO3 pebbles fabricated by wet method

Preparation of High Sphericity Li2TiO3 Tritium Breeder by Polymer Assisted Sedimentation Method

Design, synthesis and characterization of advanced tritium breeder: Li4Si1-xTixO4 ceramics

Tritium Release Performance of Biphasic Li2TiO3-Li4SiO4 Ceramic Pebbles Fabricated by Centrifugal Granulation Method

A comprehensive study on Li4Si1−xTixO4 ceramics for advanced tritium breeders

Fabrication and Improvement of the Density of Li2TiO3 Pebbles by the Optimization of a Sol–gel Method

Influence of sintering atmosphere on phase, microstructure and mechanical properties of Li4Si0.7Ti0.3O4 tritium breeding ceramics

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING