Abstract:High temperature helium gas will provide a thermal efficiency greater than 40%, even using a conventional steam turbine. In addition, helium gas will not react chemically with blanket materials, and surrounding air and water. Tritium will be easily extracted from the coolant too. Thus, it is one of the most attractive coolants for a fusion power reactor, from the economical, safety and environmental points of view. However, a large volumetric flow rate is required owing to the small heat capacity when the pressure is not extremely high. This requires a larger reactor size, larger circulating power and more penetrations, which may increase radiation streaming. A relatively low heat transfer coefficient makes it difficult to apply to a component subjected to a high heat load, such as a divertor plate. We suggest in this study, a helium-solid suspension flow as coolant, to increase the heat capacity and heat transfer coefficient. A gas pressure of 5 MPa, and inlet and outlet temperatures of 400°C and 700°C were chosen. There are few candidates for the structural material which can be used at temperatures higher than 900°C. We have proposed an intermetallic compound of titanium aluminide (TiAl) as candidate structural material of the blanket. Although the database for TiA1 is incomplete, it has high strength and ductility at the operation temperature. Using TiA1, radioactive waste management will be mitigated, since its activity will decrease rapidly. The elongation at room temperature, which is only a few per cent, will be improved through research and development not only in fusion but also in other industrial fields. In this study, spherical pebbles of lithium oxide and small blocks of beryllium were chosen as the breeder and neutron multiplier. Manganese blocks were installed to enhance energy multiplication. A tritium breeding ratio of 1.38 and energy multiplication ratio of 1.35 were obtained with the blanket. The net plant efficiency exceeds 40%, including the circulating power. The peak surface heat flux on the divertor plate was decreased with gas puffing including an impurity near the striking point. In spite of this, the expected peak heat flux was still several MW m−2 from the result of numerical calculation of the edge plasma. To remove so high a heat load, an impinging helium-solid suspension jet was applied to the high heat flux region of the divertor plate. Molybdenum alloy was used as the structural material in this region to keep the surface temperature and thermal stress lower than the design limits. TiAl was used as the structural material of other regions in the divertor chamber. To prevent excessive sputtering erosion, the electron temperature in the divertor plasma must be kept lower than 20 eV.

First Experiments on Reduction the Heat Load on the Divertor Plates of the Globus-M2 Tokamak Using Nitrogen Seeding and Their Comparison with Simulation Results

Overview of Hl-2a Experiment Results

Overview of Experimental Results on the HL-2A Tokamak

OV / 4-5 1 Overview of Experimental Results on the HL-2 A Tokamak

Impact of Impurity Mixture Gas Seeded by Supersonic Molecular Beam Injection on Edge-Localized Modes in the HL-2A Tokamak

1 EX / P 3-21 Plasma Behavior with Hydrogen Supersonic Molecular Beam and Cluster Jet Injection in the HL-2 A Tokamak

Plasma Stored Energy Analysis during Neutral Beam Injection in the Globus-M2 Tokamak Using the PET Equilibrium Code and Diamagnetic Measurements

Confinement, heating, and current drive study in Globus-M2 toward a future step of spherical tokamak program in Ioffe Institute

Hot Ion Mode in the Globus-M2 Spherical Tokamak

Thomson scattering diagnostics at the Globus M2 tokamak

Heat Load onto the Globus-M2 Tokamak Wall due to Fast Ion Loss during Development of Toroidal Alfvén Eigenmodes

Study of plasma heating in ohmically and auxiliary heated regimes in spherical tokamak Globus-M

Effect of Locked MHD Modes on the Efficiency of Plasma Heating by the Neutral Beam Injection Method at the Globus-M2 Spherical Tokamak

One-dimensional simulation and validation of divertor detachment induced through nitrogen seeding on HL-2A

Design study of helium-solid suspension cooled blanket and divertor plate for a tokamak power reactor

Synthetic Diagnostic of Spectra of Charge-Exchange Atoms for Analysis of Influence of the MHD Instability on Fast-Particle Confinement in Spherical Tokamaks Globus-M/M2

First principle-based multi-channel integrated modelling in support of the design of the Divertor Tokamak Test facility

Investigating the influence of divertor baffles on nitrogen-seeded detachment in TCV with SOLPS-ITER simulations and TCV experiments

The first observation of the hot ion mode at the Globus-M2 spherical tokamak

Improved Heat and Particle Flux Mitigation in High Core Confinement, Baffled, Alternate Divertor Configurations in the TCV tokamak

Neo-Canonical Profiles of the Electron Density and Temperature of the Plasma in the Hot Ion Mode at the Globus-M2 Tokamak