Abstract:High temperature helium gas will provide a thermal efficiency greater than 40%, even using a conventional steam turbine. In addition, helium gas will not react chemically with blanket materials, and surrounding air and water. Tritium will be easily extracted from the coolant too. Thus, it is one of the most attractive coolants for a fusion power reactor, from the economical, safety and environmental points of view. However, a large volumetric flow rate is required owing to the small heat capacity when the pressure is not extremely high. This requires a larger reactor size, larger circulating power and more penetrations, which may increase radiation streaming. A relatively low heat transfer coefficient makes it difficult to apply to a component subjected to a high heat load, such as a divertor plate. We suggest in this study, a helium-solid suspension flow as coolant, to increase the heat capacity and heat transfer coefficient. A gas pressure of 5 MPa, and inlet and outlet temperatures of 400°C and 700°C were chosen. There are few candidates for the structural material which can be used at temperatures higher than 900°C. We have proposed an intermetallic compound of titanium aluminide (TiAl) as candidate structural material of the blanket. Although the database for TiA1 is incomplete, it has high strength and ductility at the operation temperature. Using TiA1, radioactive waste management will be mitigated, since its activity will decrease rapidly. The elongation at room temperature, which is only a few per cent, will be improved through research and development not only in fusion but also in other industrial fields. In this study, spherical pebbles of lithium oxide and small blocks of beryllium were chosen as the breeder and neutron multiplier. Manganese blocks were installed to enhance energy multiplication. A tritium breeding ratio of 1.38 and energy multiplication ratio of 1.35 were obtained with the blanket. The net plant efficiency exceeds 40%, including the circulating power. The peak surface heat flux on the divertor plate was decreased with gas puffing including an impurity near the striking point. In spite of this, the expected peak heat flux was still several MW m−2 from the result of numerical calculation of the edge plasma. To remove so high a heat load, an impinging helium-solid suspension jet was applied to the high heat flux region of the divertor plate. Molybdenum alloy was used as the structural material in this region to keep the surface temperature and thermal stress lower than the design limits. TiAl was used as the structural material of other regions in the divertor chamber. To prevent excessive sputtering erosion, the electron temperature in the divertor plasma must be kept lower than 20 eV.

Improved Heat and Particle Flux Mitigation in High Core Confinement, Baffled, Alternate Divertor Configurations in the TCV tokamak

Power exhaust and core-divertor compatibility of the baffled snowflake divertor in TCV

Divertor Heat Flux Mitigation Using Supersonic Molecular Beam Injection in Type-Iii Elmy H Mode Plasmas of Hl-2a Tokamak

Investigating the influence of divertor baffles on nitrogen-seeded detachment in TCV with SOLPS-ITER simulations and TCV experiments

Performance assessment of a tightly baffled, long-legged divertor configuration in TCV with SOLPS-ITER

Divertor shaping with neutral baffling as a solution to the tokamak power exhaust challenge

An improved understanding of the roles of atomic processes and power balance in divertor target ion current loss during detachment

Performance assessment of long-legged tightly-baffled divertor geometries in the ARC reactor concept

Simulating the Impact of Baffling on Divertor Performance Using SOLPS-ITER

Physics Design of New Lower Tungsten Divertor for Long-Pulse High-Power Operations in EAST

Separating the roles of magnetic topology and neutral trapping in modifying the detachment threshold for TCV

First principle-based multi-channel integrated modelling in support of the design of the Divertor Tokamak Test facility

Dependence of divertor turbulence on plasma density and current in TCV

Divertor turbulent transport in the single null and snowflake in the TCV tokamak

Exploration of Non-Resonant Divertor Features on the Compact Toroidal Hybrid

First demonstration of Super-X divertor exhaust control for transient heat load management in compact fusion reactors

Thermo-hydraulic performance of tungsten flat tile type divertor target with two types of novel engineered cooling channel wall

Impact of divertor neutral pressure on confinement degradation of advanced tokamak scenarios at ASDEX Upgrade

Design study of helium-solid suspension cooled blanket and divertor plate for a tokamak power reactor

Ergodic divertor experiments on the route to steady state operation of Tore Supra

Broadening of the Divertor Heat Flux Profile in High Confinement Tokamak Fusion Plasmas with Edge Pedestals Limited by Turbulence in DIII-D