Abstract:The Rock Quality Designation (RQD) index is defined as the percentage of the borehole core or scanline that consists of intact lengths ≥0.1 m, and has been widely used as an engineering measure of the jointing degree of a rock mass. The directivity of RQD, which means the value of the RQD obtained from drilling cores or scanlines with different orientations can be different for a given site, is usually regarded as a drawback by researchers and engineers. This study presents a new perspective for the directivity of RQD: the directivity of RQD should be regarded as an advantage of the index because it essentially reflects the anisotropy of rock masses. Because a smaller value of the RQD index implies a better reproduction of the different jointing degrees of different rock masses, its minimum value is selected as the representative RQD (RQDr), and its corresponding direction is called as the representative direction of RQD. In this study, to obtain the RQDr and its representative direction, theoretical formulas are derived to calculate the RQD in any direction based on some known RQDs in different directions. The proposed formulas consider the variance of the discontinuity orientations and sizes for a discontinuity set, use the traditional concept of RQD, and possess the associated simplicity; they only require sampling a few additional discontinuity orientations. Therefore, the proposed approach is easy to understand and apply in engineering practices. An anisotropy index of jointing degree (AIjd) is defined to quantitatively describe the anisotropy of jointing degree for rock masses. The range of AIjd is from 0 to 100, and the larger value of AIjd reflects stronger anisotropy of jointing degree of a rock mass. In this study, a hypothetical three-dimensional discontinuity network is constructed by performing Monte Carlo simulations, based on which the generated data are analyzed to validate the proposed method. The comparison between the calculated and actual values of the RQD shows that (a) the difference between the calculated and actual values of the RQD is <4 for >86.0% of the 1368 scanlines examined with respect to 12 scanline groups, except SG4–1 group, for which the proportion is 66.2%; (b) the difference between the calculated and actual values of the RQD is <6 for >96.2% of the 1368 scanlines examined with respect to 12 scanline groups, except SG4–1, for which the proportion is 86.7%; and (c) the proposed method of calculating the RQD in any direction based on some known RQDs in different directions is satisfactory. In addition, the comparisons show that the calculated RQDr and representative direction exhibit a good agreement with the actual results, and hence, the proposed method for this purpose is satisfactory. Moreover, an actual rock mass of a slope around the Qingshan Lake National Forest Park in China is investigated, and the results show that the proposed method is valid for that rock mass.

A Novel Index (RI) to Evaluate the Relative Stability of Soils Using Ultrasonic Agitation

A New Index for Evaluating Liquefaction Resistance of Soil under Combined Cyclic Shear Stresses

Determination and Application of Microscopic Index Rca in Evaluating the Mechanical Properties of Soils

Soil Structure and Soil Organic Matter II. A Normalized Stability Index and the Effect of Mineralogy

A New Parameter to Evaluate Liquefaction Resistance of Saturated Sand under Complex Dynamic Stress Paths

Effect of Initial Pore Pressure on Undrained Shear Behaviour of Fine-Grained Gassy Soil

A New Perspective for the Directivity of Rock Quality Designation (RQD) and an Anisotropy Index of Jointing Degree for Rock Masses

A New Idea to Improve the Test Method of Soil Aggregate Stability for Soils with a Texture Gradient

Characterization and Physical Mechanisms of Aggregate Stability in Ferrisols

Estimation of Soil Shear Strength Indicators Using Soil Physical Properties of Paddy Soils in the Plastic State

Shear Modulus and Damping Ratio of Sand–Gravel Mixtures Over a Wide Strain Range

Stability and It's Mechanism of Aggregates in Easily Eroded Soils Derived from Purple Rock in the South of Zhejiang Province

EXPERIMENTAL STUDY OF INSTABILITY OF LOOSE SAND

Soil Disturbance Evaluation of Soft Clay Based on Stress-Normalized Small-Strain Stiffness

A quantitative description method for the mechanical behavior of soil-rock mixture as affected by water content

Liquefaction resistance and small strain stiffness of silty sand: Effects of host sand gradation and fines content

Physical Interpretation of Shear-Rate Behaviour of Soils and Geotechnical Solution to the Coefficient of Start-Up Friction with Low Inertial Number.

Le Bissonnais Method of Measuring Aggregate Stability in Ferrisols and Its Implications

A General Method for Quantifying the Shear Strength Anisotropy of Soil

Applicability of soil‐type index for shear wave velocity‐based liquefaction assessment

Analysis of influence factors on aggregate stability and size distribution in mollisoils