Abstract:Molybdenum disulphide (MoS2) is widely used in tribological applications because of its solid lubricating properties. However, its performance needs to be further improved. In this work, an attempt has been made to improve the tribological performance of MoS2 coating by incorporating TiO2 nanoparticles as a reinforcement material into the MoS2 base matrix. The effects of crystallite size and wt.% addition of TiO2 onto the tribological properties of composite MoS2–TiO2 have been studied. Prior to application of the coating onto the substrate surface, it was pre-treated by phosphating which leads to improvement in the porosity and helps to enhance the bond strength between the coating and steel substrate. A tribological study of composite pure MoS2 coating and MoS2–TiO2 coating was carried out using the pin-on-disc test rig at different operating conditions (contact pressure, speed and temperature). It was observed that composite MoS2–TiO2 coating exhibits excellent tribological properties as compared to pure MoS2 coating. In addition, crystallite size of TiO2 and its different weight% significantly affect the tribological properties of the composite coating. Among all samples of composite MoS2–TiO2 coating, the sample C (27.69 nm crystallite size) with 15% wt. of TiO2 depicts the lowest friction coefficient and wear rate. The influence of temperature and coating thickness on the tribological properties of composite coating has been studied. The frictional coefficient has been reduced, and the wear rate increased with an increase in temperature of the coated pin surface. The similar kind of trend has been observed with respect to the coating thickness.

Wear Performance of Electro-Fluid Mask In Situ Forming TiO2-MoS2 Alternate Coatings Under Different Friction Conditions

The effects of Ti content on tribological and corrosion performances of MoS2–Ti composite films

Tribological Behavior of MoS 2-Sb 2 O 3-Annealed Nanodiamond Coating on PEO-LST Treated Ti6Al4V

Tribological Behavior of MoS2–Sb2O3-annealed Nanodiamond Coating on PEO-LST Treated Ti6Al4V

Tribological properties of magnetron sputtered MoS2/metal (Ti, Mo) nanocomposite coatings

Tribological performance of Mn3(PO4)2 coating and PC/MoS2 coating in Rolling–Sliding and pure sliding contacts with gear oil

Effect of Modulation Periods on the Mechanical and Tribological Performance of MoS2–TiL/MoS2–TiH Multilayer Coatings

Friction and wear behaviour of composite MoS2–TiO2 coating material in dry sliding contact

Microstructure and Friction–Wear Performance of Laser Cladded Cu10Al–Ti–MoS2 Coatings Under Oil Lubrication Condition

Study on Wear and Friction Resistance of CrTiAlMoN Coatings Deposited by Magnetron Sputtering

Preparation and tribological properties of Mo/MoS2-Pb-PbS composite films

MXene/graphene oxide nanocomposites for friction and wear reduction of rough steel surfaces

Tribological properties of PEEK-based composite coating prepared by thermal spraying

Synergistic lubrication effect of OLC and MoDTC for reducing friction and wear of MAO ceramic coating on TC4 alloy

Self-lubricated nanoporous TiO 2 -TiN films fabricated on nanocrystalline layer of titanium with enhanced tribological properties

Solid Lubrication Performance of Sandwich Ti3C2Tx-MoS2 Composite Coatings

Microstructure and Tribological Behavior of TiAlSiN Coatings Deposited by Deep Oscillation Magnetron Sputtering

Improved Mechanical and Tribological Properties of TaMoN-MoSx Sputtered Film by Addition of MoS2 Lubricants

Controllable in situ fabrication of self-lubricating nanocomposite coating for light alloys

Suppressed MoO3/FeMoO4 formation in molybdenum dialkyl-dithiocarbamate-derived tribofilms on nitrogen-incorporated Al-Mg-Ti-B coatings