Abstract:In recent years, the rapidly growing consumption of fossil fuels negatively affects the environment and public health has attracted much attention. Much effort has been made to find a clean and renewable alternative energy. Bio-oil, produced by flash pyrolysis, is one of the more encouraging products for valorisation of biomass. It has been identified as a promising alternative energy source for fossil fuel owing to its outstanding characteristics such as higher energy density, more suitable for storage and transportation, less capital investment than any other products of biomass. However, the nature of bio-oil contains high acidity, strong corrosiveness, low heating value, thermal instability and chemical complexity, which severely restrict its wide range of applications as a high quality energy. Therefore, it is necessary to upgrade bio-oil. The upgrading techniques include steam reforming, esterification, emulsification, hydrodeoxygenation, catalytic pyrolysis etc. In this paper, catalytic pyrolysis experiments were performed in a fixed bed with inner diameter of 16mm and height of 380mm for bio-oil model compounds (diacetone alcohol, furfural, ethyl acetate and guaiacol) over different characteristics zeolites (HY, HZSM-5, ZSM-5, P/ZSM-5, La/ZSM-5, Ni/ZSM-5) at the condition of T=400℃, WHSV=4 h-1. The catalysts physical properties were investigated by BET (Brunauer-Emmett-Teller surface area) analyse. Water content was detected by using the method of Karl Fischer (870 KF Titrino). The GC-MS was used to analyze the major constituents of the pyrolytic products qualitatively and quantitatively. After the addition of La, the pore size increased from 0.61 nm (ZSM-5) to 0.89 nm (La-ZSM-5). On the contrary, the pore size of P modified ZSM-5 is 0.49 nm which is smaller than that of ZSM-5. The pyrolytic products of the model compounds included organic fraction, water, coke and gas. Compared with ZSM-5,the coke deposition over the La modified ZSM-5 decreased from 2.61% to 1.99% and the organic fraction increased dramatically from 46.10% to 61.51%, which showed the best performance in terms of products distribution among all modified catalyst. The conversions of overall model components and single model component were calculated respectively. The difficulty of the model components pyrolysis is guaiacol>furfural>ethyl acetate>diacetone alcohol. By adding catalysts, the conversion of totally compounds were increased in different degrees, which meaned zeolite promoted the degree of catalytic pyrolysis. HZSM-5 had a best catalytic pyrolysis activity with the highest totally compounds conversion rate of 65.98%. There was a slight decline in the conversion of model compounds contrasted ZSM-5 with La/P/Ni modified ZSM-5. The major components of catalytic pyrolysis were aromatic hydrocarbons, ketones, phenols and so on. It means that a series of decarboxylation and decarbonylation reactions were taken place during the pyrolysis process. On the one hand, the reduction of the oxygen content of bio-oil help to improve its stability, on the other hand it will enhance its heating value. The optimal selectivity of aromatic reached 7.36% over HZSM-5. The La modified ZSM-5 improved the selectivity of aromatic from 6.72%to 7.28%. The highest yield of saturated alcohol was 7.1%over ZSM-5 and decreased using modified ZSM-5. According to the catalytic pyrolysis products distribution, the different reaction pathways for model compounds were discussed, which provided a theoretical basis for experimental study of upgrading bio-oil.

One-pot synthesis of lignin biochar supported Ni for catalytic pyrolysis of Chlorella vulgaris and its model compounds: The formation mechanism of aromatic hydrocarbons

Ni 12 P 5 /P–N–C Derived from Natural Single-Celled Chlorella for Catalytic Depolymerization of Lignin into Monophenols

Catalytic Hydropyrolysis of Lignin Using NiMo-doped Catalysts: Catalyst Evaluation and Mechanism Analysis

Nickel loaded on biochar prepared from different carbon sources for selective hydrogenolysis of diphenyl ether

Selective cleavage of C–O bond in lignin and lignin model compounds over iron/nitrogen co-doped carbon supported Ni catalyst

Efficient depolymerization of alkali lignin to monophenols using one-step synthesized Cu–Ni bimetallic catalysts inlaid in homologous biochar

Catalytic pyrolysis of bio-oil model compounds over La/P/Ni modified ZSM-5

Catalytic mechanism of N-containing biochar on volatile-biochar interaction for the same origin pyrolysis

Catalytic Pyrolysis of Tar Model Compound with Various Bio-Char Catalysts to Recycle Char from Biomass Pyrolysis

Hydrogen-rich syngas production from biomass pyrolysis and catalytic reforming using biochar-based catalysts

Selective catalytic conversion of Kraft lignin into monoaromatic hydrocarbons over niobium oxide catalysts

Catalytic Cleavage of the C–O Bond in Lignin and Lignin-Derived Aryl Ethers over Ni/AlPyOx Catalysts

Catalytic fast pyrolysis of enzymatic hydrolysis lignin over Lewis-acid catalyst niobium pentoxide and mechanism study

Improved nickel nanocatalysts for selective cleavage of lignin model compounds and lignin

Sustainable aromatic production from catalytic pyrolysis of lignin mediated by a novel solid Lewis acid catalyst

Importance of oxygen-containing functionalities and pore structures of biochar in catalyzing pyrolysis of homologous poplar

Integrated Production of Aromatic Amines and N-Doped Carbon from Lignin Via Ex Situ Catalytic Fast Pyrolysis in the Presence of Ammonia over Zeolites

One-step catalytic hydrotreatment of lignin dimer model compounds to cycloalkane and cycloalcohol by spherical metal-organic framework derived NiLa bimetallic materials

Preparation of High Catalytic Activity Biochar from Biomass Waste for Tar Conversion

Highly efficient catalytic hydrogenolysis of lignin model compounds over hydrotalcite-derived Ni/Al 2 O 3 catalysts

Selective Hydrogenolysis of Lignin Model Compounds to Aromatics over a Cobalt Nanoparticle Catalyst