Abstract:Organic-inorganic hybrid perovskite solar cells have attracted tremendous research interests due to their amazing light to electric power conversion efficiencies (PCEs).In the past four years,the PCE of perovskite solar cells has significantly increased up to 22.1％,which outperforms several other types of third-generation solar cells and becomes the most promising candidate to compete with the traditional silicon-based solar ceils.This result is mainly owing to some excellent properties of the hybrid perovskite active layer,such as a high absorption coefficient,an appropriate band gap and a long carrier diffusion length.Nevertheless,most of the reported high efficiencies were only achieved with very small active areas in the range of 0.03 to 0.2 cm2,which is likely to cause measurement errors.What is worse,the material utilization ratio is only 1％ during film deposition,hindering the industrial production of perovskite solar cells in the future.Therefore,a large-scale production process has become a big challenge to realize the purpose of commercial applications.To date,the best certified PCE of 19.6％ has been obtained with an active area exceeding 1 cm2.The most important aspect is fabricating large-area uniform,pinhole-free and large crystal grain perovskite thin films for scaling up high PCE perovskite solar cells.To realize the purpose of large-area,high-quality perovskite film fabrication,a range of thin film fabrication techniques have been proposed,including spin-coating,vacuum flash-assisted solution process (VASP),doctor blading,slot-die coating,inkjet printing,spray coating,vapor assisted deposition and soft-cover deposition.This review aims at giving an overview of these thin film deposition techniques for the processing of perovskite thin film fabrication.By comparing the film quality and material utilization ratio corresponding to different film deposition methods,the studies on perovskite thin film fabrication techniques are summarized.Among these techniques,spin-coating has been widely used in laboratory for perovskite film fabrication,but the material utilization ratio is usually less than 1％,hindering the fabrication of perovskite film with large-area.Spin-coating combined with VASP exhibits an amazing result for high-quality perovskite film fabrication,but it still has a low material utilization ratio in spin-coating process.Other techniques,like doctor blading,slot-die coating and inkjet printing are suitable for large-area perovskite film fabrication with high material utilization ratio.Spray coating and soft-cover deposition also have shown great potential for large-area perovskite film fabrication.The PCEs of perovskite solar cells have reached 13％ and 17％ with an active area exceeding 1 cm2,respectively.Particularly,a high-quality perovskite film with a large-area of 51 cm2 was obtained by soft-cover deposition,which made this technique more promising for the development of perovskite solar cells in the future.Based on this review,we suggest that VASP is a suitable technique for depositing high-quality large-area perovskite film.It would be a promising technique to combine VSAP with other techniques,such as doctor blading,inkjet printing,etc.,to enhance material utilization ratio for large-scale perovskite solar cells.In addition,some simpler and lower-cost techniques should be developed for the fabrication of perovskite solar cells in the future.

Smooth perovskite thin films and efficient perovskite solar cells prepared by the hybrid deposition method

te thin fi lms and e ffi cient perovskite solar cells prepared by the hybrid deposition method †

Fabrication of Semi-Transparent Perovskite Films with Centimeter-Scale Superior Uniformity by the Hybrid Deposition Method

Formation of Ultrasmooth Perovskite Films Toward Highly Efficient Inverted Planar Heterojunction Solar Cells by Micro-Flowing Anti-Solvent Deposition in Air

Low-Temperature Soft-Cover Deposition of Uniform Large-Scale Perovskite Films for High-Performance Solar Cells

Collaborative Fabrication of High-Quality Perovskite Films for Efficient Solar Modules through Solvent Engineering and Vacuum Flash System

Approximately 800-Nm-thick Pinhole-Free Perovskite Films Via Facile Solvent Retarding Process for Efficient Planar Solar Cells

Perovskite hybrid evaporation/ spin coating method: From band gap tuning to thin film deposition on textures

mi-transparent perovskite fi lms with centimeter-scale superior uniformity by the hybrid deposition method †

A solvent- and vacuum-free route to large-area perovskite films for efficient solar modules

High Performance Perovskite Solar Cells by Hybrid Chemical Vapor Deposition

Perovskite films prepared by solvent volatilization via DMSO-based intermediate phase for photovoltaics

Large-area Thin Film Deposition Technologies for Fabricating Hybrid Perovskite Solar Cells

Formation of High-Quality Perovskite Thin Film for Planar Heterojunction Solar Cells

Solution-induced morphology change of organic-inorganic hybrid perovskite films for high efficiency inverted planar heterojunction solar cells

A fabrication process for flexible single-crystal perovskite devices

Facile preparation of organometallic perovskite films and high-efficiency solar cells using solid-state chemistry

Perovskite solar cells by vapor deposition based and assisted methods

Efficient Perovskite Hybrid Solar Cells Via Controllable Crystallization Film Morphology

Solvent-assisted Growth of Organic–inorganic Hybrid Perovskites with Enhanced Photovoltaic Performances

Simple and effective deposition method for solar cell perovskite films using a sheet of paper