Abstract:Background: Combined infrared (CIR) and convective drying is a promising technology in dehydrating heat-sensitive foods, such as fruits and vegetables. This novel thermal drying method, which involves the application of infrared energy and hot air during a drying process, can drastically enhance energy efficiency and improve overall product quality at the end of the process. Understanding the dynamics of what goes on inside the product during drying is important for further development, optimization, and upscaling of the drying method. In this study, a multiphase porous media model considering liquid water, gases, and solid matrix was developed for the CIR and hot-air drying (HAD) of sweet potato slices in order to capture the relevant physics and obtain an in-depth insight on the drying process. The model was simulated using Matlab with user-friendly graphical user interface for easy coupling and faster computational time. Results: The gas pressure for CIR-HAD was higher centrally and decreased gradually towards the surface of the product. This implies that drying force is stronger at the product core than at the product surface. A phase change from liquid water to vapour occurs almost immediately after the start of the drying process for CIR-HAD. The evaporation rate, as expected, was observed to increase with increased drying time. Evaporation during CIR-HAD increased with increasing distance from the centreline of the sample surface. The simulation results of water and vapour flux revealed that moisture transport around the surfaces and sides of the sample is as a result of capillary diffusion, binary diffusion, and gas pressure in both the vertical and horizontal directions. The nonuniform dominant infrared heating caused the heterogeneous distribution of product temperature. These results suggest that CIR-HAD of food occurs in a non-uniform manner with high vapour and water concentration gradient between the product core and the surface. Conclusions: This study provides in-depth insight into the physics and phase changes of food during CIR-HAD. The multiphase model has the advantage that phase change and impact of CIR-HAD operating parameters can be swiftly quantified. Such a modelling approach is thereby significant for further development and process optimization of CIR-HAD towards industrial upscaling. © 2020 Society of Chemical Industry.

Multiphysics modeling of wire-to-plate electrohydrodynamic drying with air crossflow

A fully coupled multiphase model for infrared-convective drying of sweet potato

CFD design and testing of an air flow distribution device for microwave infrared hot-air rolling-bed dryer

CFD Simulation of High-Temperature Effect on EHD Characteristics in a Wire-Plate Electrostatic Precipitator

Numerical Modeling of Air Flow in a Cabinet Dryer Equipped by Deflector Plates

Numerical analyses of wire-plate electrohydrodynamic flows

Multiphysics Modeling of Electrode Dissolution Under Hydrodynamic Conditions in Low Conductivity Water

A Thermo-Hydro-Mechanics Bidirectional Coupling Mathematical Model for Drying of Biological Porous Medium

Selection of Convective Moisture Transfer Driving Potential and Its Impacts Upon Porous Plate Air-Drying Characteristics

Design optimization of hollow fiber membranes for passive air dehumidification in drying applications

Characterization of Wicking Performance for Open Rectangular Microgrooves under Planar EHD Effects in Two-Phase Heat Transfer Devices

Modeling and Analysis of the Drying Process of Lithium-Ion Battery Electrodes Based on Non-Steady-State Drying Kinetics

Numerical analysis and optimization of heat transfer enhancement on a flat plate by an EHD jet

Multiphase modelling of water evaporation and condensation in an air-heated porous medium

Multiphysics Digital Model of the High Frequency Transformer for Power Electronics Application Considering Electro-thermal Interactions

Investigation of heat and mass transfer of oldroyd – 8 constant fluid in wire coating process employing response surface methodology

Experimental and Numerical Investigation of Corona Discharge Induced Flow on a Flat Plate

Computational fluid dynamic simulation of packed bed drying process: impact of particle properties, drying conditions, and lateral edge heating modes on drying kinetics

Numerical Investigation of Wafer Drying Induced by the Thermal Marangoni Effect

Heat flow topology-driven thermo-mass decoupling strategy: Cross-scale regularization modeling and optimization analysis

Investigating the Impact of Electrode Wire Interaction on EHD Flow in Two-Wire-to-Plate Corona Devices: A Computational Analysis